Belanger Chameleon Arch Series Скачать руководство пользователя страница 27

Страница: 27 / 90

CHAMELEON® ARCH SERIES

1MANUL526

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Installation

Tunnel Placement

When placing a piece of equipment, tunnel depth will vary from site to site. Be sure to allow an
adequate operating envelope when placing the Arch.

Stand the Arch up at this point in its proper location.

Note:

Each Arch head beam weldment has a welded stud on one side of the weldment. These
studs will need to face towards the exit of the bay.

2) Remove the 8 lag bolts from the accessory box and secure the driver side leg to the

floor using only one of the four holes on the base plate. If you have guide rail installed at
your site, use the measurement in the image below for proper location from the drive
side leg.

Overhead View

Dimensions are taken from the outer equipment leg to the driver side edge of the inside guide rail

3) Square the Arch up to the bay. Secure the passenger side leg to the floor using all four

lag bolts, making sure that the Arch is level in both directions. If so, finish securing the
driver side leg to the floor.

Note:

If you have a Utility Arch, proceed to the Neon Strip Kit Installation and Electrical

Connections section. If you have a Spray Arch, continue to the next step.

Continuing the Arch Assembly

Spray Arch Only:

Remove the Arch side spray manifolds from the skid. They should

have the nozzle extensions and barbed hose fittings in them already.

Spray Arch Only:

Slide the two remaining ear clamps over the ends of the blue water

hose and secure the hose to the side spray manifolds.

Direction

Of Travel

Before

After

43-1/2

”

(1.10 m)

Содержание Chameleon Arch Series



























































































Результаты поиска

Содержание Chameleon Arch Series

Отзывы:

Похожие инструкции для Chameleon Arch Series

Бренды по названию

Популярные бренды

Belanger Chameleon Arch Series, Руководство пользователя

Результаты поиска

Содержание Chameleon Arch Series

Отзывы:

Похожие инструкции для Chameleon Arch Series

Бренды по названию

Популярные бренды