Belanger Chameleon Arch Series Скачать руководство пользователя страница 41

Страница: 41 / 90

CHAMELEON® ARCH SERIES

1MANUL526

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Installation

Additional Options: Foam Pods

Single Foam Pods and Triple Foam Pods

Note:

If you have extension brackets for your foaming pods, mount one to each angle using the

supplied 3/8-16 fasteners and washers.

3) Mount the foaming pod assemblies to either the angle or the extension bracket using the

fasteners and washers as shown in the images below.

Adjustment to the angle of the

foam pod spray pattern can be done once all of the lines and hookups have been
completed.

The image above shows the Singe Foaming Pod. The Triple Foaming Pod mounts the same way. Keep in mind that the pods can be

mounted in an inverted position but you will have to change them from one leg to the othe

r as explained in the “Things

You Should

Know” sec

tion.

Note:

The foaming pods can be mounted two different ways. Refer to the illustrations below for

more details on how this is done.

4) Remove the center feed assembly from the accessory box. If you are hooking up single

foam pods, you will have been shipped two, tee/elbow assemblies.

If you are hooking up triple foam pods, you will have been shipped an aluminum
manifold assembly.

After

Before

Tee/Elbow
Assemblies

Aluminum Manifold
Assembly

Содержание Chameleon Arch Series



























































































Результаты поиска

Содержание Chameleon Arch Series

Отзывы:

Похожие инструкции для Chameleon Arch Series

Бренды по названию

Популярные бренды

Belanger Chameleon Arch Series, Руководство пользователя

Результаты поиска

Содержание Chameleon Arch Series

Отзывы:

Похожие инструкции для Chameleon Arch Series

Бренды по названию

Популярные бренды