BelAir Networks BelAir 100SN Скачать руководство пользователя

Страница: 54 / 212

BelAir100SN User Guide

System Settings

May 31, 2010

Confidential

Page 54 of 212

Document Number BDTM11001-A01 Released

Example

/system# show restart-reason

Previous reboot was a cold restart initiated by user.

Creating and

Using Script Files

You can use script files to:
• make repetitive tasks quicker and easier to do

• automate the configuration of a node when it starts up. See

“BelAir100SN

Auto-configuration” on page 63

The BelAir100SN provides several CLI commands to manage script files.

Script Creation

Guidelines

Use the following guidelines to create a script file:

• Make sure the script contains only valid and supported BelAir CLI

commands. If you are using an older script, make sure the CLI commands

that it contains are still valid and supported.

• Some BelAir node functions, such as Network Address Translation (NAT),

require that you reboot the node after you configure them. If your script is

for BelAir100SN auto-configuration at startup and if it must include the

reboot

command, then your script must include special declarations. For

details, see

“Guidelines for Using the reboot Command in a Script” on

page 58

Caution!

Using the

reboot

command in an auto-configuration script without the correct

declarations may cause the node to enter a continuous

reboot

loop.

• Test the final script to ensure all commands are valid, syntactically correct

and appropriate for the installed hardware.

Put the final script on a TFTP, FTP or FTPS server to transfer the script file to

the BelAir unit.

Specifying a Physical

Interface in Script

Script files can use the following method to ensure commands are applied to
the correct physical interface:

1 Begin the command sequence by specifying the physical interface with the

following declaration:

int[-<asbly>]-<iftype>[-<desc>]-<instance>

<asbly> specifies the node’s assembly code. This part of the declaration is
optional. If provided, it must match at least part of the text in the

Assembly

Содержание BelAir 100SN





















































































































































































































Результаты поиска

Содержание BelAir 100SN

Отзывы:

Похожие инструкции для BelAir 100SN

Бренды по названию

Популярные бренды

BelAir Networks BelAir 100SN, Руководство пользователя

Результаты поиска

Содержание BelAir 100SN

Отзывы:

Похожие инструкции для BelAir 100SN

Бренды по названию

Популярные бренды