background image

22

5.5.11 Set time:  

5Et t

Set time is the Timer's setpoint. When controlling an
external event via the optional control outputs the
BA578E will time-down from the set time to zero or
time-up from zero to the set time.

To check or change the set time, select

5Et t

from

the configuration menu and press

(

which will

reveal the existing setting displayed in the units
defined by the

unit5

function with the most

significant digit flashing. The flashing digit may be
adjusted by pressing the

*

or

&

button followed

by the

(

button to transfer control to the next digit.

When set as required, enter the selection and return
to the

5Et t

prompt in the configuration menu by

operating the 

)

 button. 

Can also be adjusted from Timer display mode, see
5.5.16.

Note:

If

5Et t

is zero the Timer will not function

when an external start input is received or the

&

button is operated.

5.5.12 Repeat timing cycle:  

CYCLE5

This a powerful function which allows the BA578E
timing cycle to be repeated up to 99 times or
continuously with a configurable delay between
cycles of up to 99hours, 59 minutes & 59 seconds.

To check or adjust the repeat timing cycle, select

cycle5

from the configuration menu and press

(

which will enter a sub-menu containing three

sub-functions,

EnbL

,

CYCL Cnt

and

r5t dELA

which

are described in the following sections.

5.5.13 Cycle function enable:  

EnbL

This sub-function allows the repeat timing cycle to
be enabled or disabled without altering any of the
repeat timing cycle parameters. To check or change
the function select

EnbL

from the repeat timing cycle

sub-menu

cycle5s

and press

(

which will reveal if

the repeat cycle function is

on

or

oFF

. The setting

can be changed by pressing the

&

or

*

button

followed by the

)

button to return to the repeat

timing cycle sub-menu.

5.5.14 Cycle count:  

cycl cnt

This sub-function defines the number of times the
timer cycle is repeated. It may be set to any number
between 1 and 99, or to 00 for continuous repetition.
To check or change the function select

cycl cnt

from the repeat timing cycle sub-menu

cycle5

and

press

(

which will reveal the number of times the

timer cycle is to be repeated with the most
significant flashing.

The flashing digit may be

adjusted by pressing the

*

or

&

button followed

by the 

button to transfer control to the next digit.

When set as required, enter the selection and return
to the

cycl cnt

prompt in the sub-menu by operating

the 

)

 button.

5.5.15 Restart delay:  

r5t dela

This sub-function defines the time delay between
repeat timing periods.

It is shown in the format

selected in the units function and may be set to any
time between zero and the maximum time allowed in
the selected format.

  

Time format

Maximum delay

  selected in

unit5

12 : 00 : 00

99 : 59 : 59

12 : 00

99 : 59

      30 : 00

  5999  : 59

            30

     359999

To check or change the restart delay time select

r5t dela

from the repeat timing cycle sub-menu

cycle5

and press

(

which will reveal the delay

time in the selected format with the most significant
digit flashing. The flashing digit may be adjusted by
pressing the

*

or

&

button followed by the

(

button to transfer control to the next digit. When

set as required, enter the selection and return to the

r5t dela

prompt in the sub-menu by operating the

)

 button.

Can also be adjusted from Timer display mode, see
5.5.16.

5.5.16 Adjusting the set time 

5Et t 

and restart

 

delay

  r5t dela 

 from the display mode: 

 

AC5Et t

When this function is enabled the Timer's set time

5Et t

and restart delay

r5t dela

can be adjusted

from the display mode by simultaneously operating
the

(

and

*

push buttons. Thus allowing an

operator to adjust these parameters without having
access to the instrument's configuration menu. The
function contains two sub-functions,

EnbL

which

activates the function and

ACCd

which defines a

separate code for access to

5Et t

with the Timer in

the display mode.

To check or change the function, select

AC5Et t

in

the configuration menu and press

(

which will

reveal the

EnbL

prompt, pressing

(

again will show

if the function is

on

or

oFF

. If adjustment of the set

time from the display mode is not required press the

*

or

&

button to select

no

and then press

)

t

wice to return to the configuration menu. If the

function is required, select

YE5

and press

)

to

return to the

EnbL

prompt from which

ACCd

, which

allows a separate access code to be entered, can
be selected by pressing the 

*

 or 

&

 button.

Содержание BA578E













































Отзывы: