background image

19

5.5.8

Lower display:   

di5P-2

The configuration options for the lower display vary
depending upon whether the repeat timer function

cycle5

 is enabled.

CYCLE5

 disabled

When the lower display is enabled it shows the
set time 

5ET t

CYCLE5

 enabled

When the lower display is enabled it shows the
total number of repeat cycles requested together
with the number of cycles performed. During the
delay time between cycles the display shows the
time until the next cycle starts.  
Menu options allow each part of the cycle to be
briefly identified at the start of each part, or
periodically throughout the cycle.

To check or change the configuration of the lower
display select

di5P-2

from the configuration menu

and press

(

which will reveal the existing setting

which can be changed by pressing the

*

or

&

button followed by the

)

button to enter the

selection and return to the configuration menu.

If the

CYCLE5

function is not enabled the

following two options are available:

5td

Lower display shows the Timer's set time

5Et t

, to which the BA578E will time-up to,

or time-down from, depending upon the
direction of count selected in the

uP or dn

function.

oFF

 

Lower display disabled.

If the

CYCLE5

function is enabled the following

three options are available:

5td

Lower display shows the number of cycles
requested together with the current cycle
number.

During the configurable delay

period between cycles the display times-
down from the requested delay to zero. A
brief notification of timer status i.e.

CYCLE

or

dELAY

is shown at the start of each

period.

02 -11

Current

Number of cycles

cycle number.

requested, not

shown when cycle is

 continuously repeated.

LabEL

Exactly the same as

5td

, but timer status

i.e. 

CYCLE

 or 

dELAY

 is shown periodically.

oFF

 

Lower display disabled.

5.5.9

Starting & stopping the Timer:  

5tAr5toP

The Timer may be started and stopped by signals on
Input A and Input b, or by operation of the front panel

*

 or 

&

 push buttons.

To check or change the control of the Timer, select

5tAr5toP

from the configuration menu and press

(

which will reveal the existing setting which can be
changed by pressing the

*

or

&

button followed

by the

)

button to enter the selection and return to

the configuration menu. The options available are
shown in the following tables.

Voltage inputs and control from front panel

Display

Start

Stop

ControL 1

A input high

b input high

ControL 2

A input low

b input low

ControL 3

A input high

A input low

ControL 4

A input low

A input high

LoCAL

&

 button

*

 button

Contact and open collector inputs

Display

Start

Stop

ControL 1

A open

b open

ControL 2

A closed

b closed

ControL 3

A open

A closed

ControL 4

A closed

A open

Proximity detector input

Display

Start

Stop

ControL 1

A low current

b low current

ControL 2

A high current

b high current

ControL 3

A low current

A high current

ControL 4

A high current

A low current

5.5.10    Units of display:  

unit5

Defines the format of all displayed times, except the
delay time of the status output and optional control
outputs which are always shown in seconds and the
grand total which is always shown in hours and
tenths of an hour.

To check or change the units of display, select

unit5

from the configuration menu and press

(

which

will reveal the existing setting which can be changed
by pressing the

*

or

&

button followed by the

)

button to enter the selection and return to the
configuration menu.

The options available are

shown in the following tables:

Display

12 : 00 : 00

Hours, minutes & seconds

12 : 00

Hours & minutes

*

     

30 : 00

Minutes & seconds

           

30

Seconds

*

Only available when time specified in seconds for

5et t

and r5t

dela

are zero or exactly divisible by

60.

The Timer's maximum elapsed time in any format is
equivalent to 99hours, 59 minutes & 59 seconds.

Содержание BA578E













































Отзывы: