BEKA BA374NG Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 53

background image

13

5.

ACCESSORIES

5.1

Display backlight

The BA374NG Timer or Clock can be supplied with
a factory fitted backlight that produces green
illumination enhancing display contrast and enabling
it to be read at night or in poor lighting conditions.
The backlight is internally powered from the
instrument power supply so no additional wiring is
required, but the supply current increases as shown
below.

BA374NG

configured as Timer

current

consumption

BA374NG Timer or Clock

10mA

Additional for backlight

16mA

Addition with terminals 3 & 4 linked

6mA

Addition with terminals 7 & 8 linked

6mA

---------------

Total current

38mA max

BA374NG

configured as Clock

current

consumption

BA374NG Timer or Clock

10mA

Additional for backlight

16mA

---------------

Total current

26mA max

5.2

Control outputs

Although the dual isolated control outputs are factory
fitted options, they are described in the main body of
this instruction manual as they will be used for the
majority of applications. If control outputs are
required they should be specified when the
instrument is ordered.

5.3

Units of measurement & instrument
identification.

New BA374NG Timer or Clocks are supplied with a
printed  scale  card  showing  the  units  of
measurement  and  tag  information  specified  when
the instrument was ordered.  If this information was
not supplied a blank scale card will be fitted which
can  easily  be  marked  with  a  dry  transfer  or  a
permanent marker on-site.

Custom printed scale cards are available as
accessories and may be easily fitted as shown in
section 4.4 of this manual.

5.4 Legend plate

The BA374NG can also be supplied with a blank or
custom laser engraved stainless steel legend plate -
see   Fig   8.     The   plate,   which   after   installation   is
visible from the front of the instrument, is supplied
loose  with  two  fixing  screws for securing  it to  the
rear  of the instrument's back-box.  This plate  can
typically accommodate:

1 row of 5 alphanumeric characters 10mm high

or 1 row of 6 alphanumeric characters 7mm high

or 2 rows of 10 alphanumeric characters 5mm high

5.5 BA393G pipe mounting kit

316 stainless steel pipe mounting kit, attaches a
BA374NG to any vertical or horizontal pipe with an
outside diameter between 40 and 73mm.

5.6 BA394G panel mounting kit

The  BA374NG  may  be  panel  mounted  using  a
BA394G  stainless  steel  panel  mounting  kit.    This
secures  the  BA374NG  into  a  panel  aperture  and
maintains the ingress protection of the instrument,
but it does not provides an IP66 seal between the
front and rear of the panel in which the BA374NG
Timer or clock is mounted.

«
...
11
12
13
14
15
...
»

Содержание BA374NG






















































Отзывы:

Нет отзывов

Похожие инструкции для BA374NG

Бренд: Keithley Страницы: 49

Бренд: National Instruments Страницы: 15

Бренд: Vaisala Страницы: 2

Бренд: Veeder-Root Страницы: 59

CP-4900 Micro-GC

Бренд: Varian Страницы: 13

Бренд: janitza Страницы: 85

micro-TRI-gloss ?

Бренд: BYK Страницы: 174

SoundAdvisor NMS045

Бренд: Larson Davis Страницы: 64

Бренд: Tenma Страницы: 52

Бренд: Hanna Instruments Страницы: 2

Бренд: Zero 88 Страницы: 32

Бренд: Dakota Digital Страницы: 34

Бренд: Value Страницы: 20

HX3 Drawbar Expander Version 5

Бренд: KEYBOARDPARTNER Страницы: 11

SensoDirect Con200

Бренд: Lovibond Страницы: 24

Бренд: horiba Страницы: 103

Бренд: Hanna Instruments Страницы: 11

Бренд: Kawai Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды