BEKA BA374NG Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 53

background image

12

4.3

EMC

The BA374NG complies with the requirements of the
European EMC Directive 2014/30/EU. For specified
immunity all wiring should be in screened twisted
pairs, with the screens earthed at one point in the
safe area.

4.4

Units of measurement and tag marking
on scale card.

The Timer or Clock's units of measurement and tag
information are shown on a scale card which slides
into the instrument.

New  Timer  or  Clocks  are  supplied  with  a  printed
scale  card  showing  the  requested  units  of
measurement  and  tag  information.    If  this
information is not supplied when the instrument is
ordered, a blank scale card will be fitted which can
easily  be  marked  on-site  with  a  dry  transfer  or  a
permanent marker.  Custom printed scale cards are
available from BEKA associates as an accessory.

To remove the scale card from a Timer or Clock
carefully pull the transparent tab at the rear of the
instrument assembly away from the assembly as
shown in Fig 9a.

Fig 9a Removing scale card

To replace the scale card carefully insert it into the
slot on the right hand side of the input terminals as
shown in Fig 9b. Force should be applied evenly to
both sides of the scale card to prevent it twisting.
The card should be inserted until about 2mm of the
transparent tab remains protruding.

Fig 9b Inserting scale card into the

instrument assembly.

«
...
10
11
12
13
14
...
»

Содержание BA374NG






















































Отзывы:

Нет отзывов

Похожие инструкции для BA374NG

Бренд: Hammond Страницы: 78

Бренд: ISKRAEMECO Страницы: 12

RAVTD1760WS Series

Бренд: Ravaglioli Страницы: 24

Stream Line Pro

Бренд: Halo Photonics Страницы: 45

Stubby LED-1500

Бренд: Dive Perfect Страницы: 4

Бренд: QuantAsylum Страницы: 35

Бренд: Xsensor Страницы: 13

Бренд: RAM Страницы: 43

Бренд: ScienTECH Страницы: 43

Бренд: Eddy Wireless Страницы: 18

Expert PDU energy 8001

Бренд: Gude Страницы: 22

Бренд: ILITCH ELECTRONICS Страницы: 2

Бренд: OrienTek Страницы: 2

Бренд: Fora Страницы: 10

Бренд: DAKOTA ULTRASONICS Страницы: 51

Бренд: GARO Страницы: 15

Бренд: Mountz Страницы: 27

Бренд: National Instruments Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды