manualshive.com logo in svg

BEINAT BX444-Mc, Руководство пользователя

Поделиться
Скачать
BEINAT BX444-Mc Скачать руководство пользователя страница 9

Page  9

Selection  of  the  type  of  gas  monitored  by  each  probe
The  BX444-Mc  if  fitted  with  four  micro-switches  in  order  to  select  the  type  of  gas  that  the  connected  probes
should  monitor.
The  LEL  reading  is  obtained  by  shifting  the  switch  to    ON.         Explosive  gas.
The  ppm  reading  is  obtained  by  shifting  the  switch  to  OFF.      Toxic  gas

Components and Commands continue

Switch  1  –  Selection  of  the  intrinsic  safety
In  the    ON  position,  the  intrinsic  safety  function  is  enabled.
In  the  OFF  position,  the  intrinsic  safety  function  is  disabled

Switch  2  -  Working  Mode    of  Main  alarm  relay
In  the  OFF    (impulse)  position,  the  relay  remains  closed  for  seconds,  and  then  disenergizes  afterwards.
In  the  ON  (continuous)  position,  the  relay  remains  closed  until  the  RESET  button  is  pressed.

Switch  1  (3)  -  Alarm  memory  logging
By setting  the micro-switch to ON, the device will log the  alarm, maintain  the relay closed, and  the main  alarm
LED  will  blink,  until  the  RESET  button  is  pressed.
By  setting  the  micro-switch  to  OFF,  the  device  will  not  maintain  the  alarm  memory  and  the  relay  switches
off  when  the  connected  probe  no  longer  detects  gas;    In  compliance  with  the  rules  this  function
becomes  active  only  when  you  select  the  detection  of  Toxic  Gases  (reading  in  “ppm”)

Switch  2  (4)  -  Selecting  of  the  control  unit  in  oxygen  detection  mode
By  setting  the  micro-switch  to  ON,  the  device  is ready to  detect  the oxygen.  The  display  changes  color  and
becomes  BLU

ATTENTION  !!  Selecting  the  detection  of  oxygen  the  control  unit  will  be  enabled  to  detect  OXYGEN,
and  not  other  types  of  Gas

By  setting  the  micro-switch  to  OFF,  The  control  unit  is  ready  to  explosive  or  toxic  gas  detection.
The  display  changes  color  and  becomes  green.

Zone1  Zone2    Zone3  Zone4

Micro-switch  (2)  to  select  the  type  of  gas  monitored
Position ON  lreading  in  LEL  -  Explosive  gas
Position OFF  reading  in  ppm  -  Toxic  gas

Light  signaling  the  type  of  gas  selected
ppm  is  the  reading  of  the  concentration  for  the  CO  gas
LEL    is  reading  of  the  concetrazione  for  Explosive  Gas  (Methane  or  LPG)

ppm              LEL

Relay’s  working  mode  and  the  memory  of  the  Main  alarm

Zone1  Zone2    Zone3    Zone4

Micro-switch  1  Positive  Safety
Micro-switch  2  working  mode  of  the  Main  Alarm  relay
Micro-switch  3  Maintaining  Memory
Micro-switch  4  Enabling  Oxygen  mode

1  2     3   4

Содержание BX444-Mc













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды