Beijer Electronics BFI-H3, Стартап

Страница: 27 / 32

Beijer Electronics Frequency Inverter BFI-H3
KI00363D 2021-07
www.beijerelectronics.com
27 (32)
6.7 Monitoring from Keypad
Parameter group 0 contain variables to be monitored as table below:
Description Display range Explanation
P0-01
1st Analog Input Value -100 % to 100% 100% = max input voltage
P0-02
2nd Analog Input Value 0 to 100% 100% = max input voltage
P0-03
Digital Input Status 00000 to 11111 MSB: Dig In1 / LSB: Dig In 5
P0-04
Speed Reference Input -P1-
01 … P1-01
Displayed in Hz if P-10 = 0, otherwise displayed in RPM
P0-07
Fieldbus Speed Reference -P1-
01 … P1-01
Displays se-point received from Fieldbus interface.
P0-08
PID Reference 0 to 100 % Displays the setpoint input to the PID controller.
P0-09
PID feedback 0 to 100 % Displays the feedback value to the PID controller.
P0-11
Motor Voltage
0 … 600V AC
Value of RMS voltage applied to motor
P0-13
Trip Log Displays the four latest fault codes
P0-19
Cascade Run Time Log hours
Run Time values for pumps in cascade mode.
0 = Master, 1 = Pump1, 2 = Pump2
P0-20
DC Bus Voltage
0 … 1000V dc
Internal DC bus voltage
P0-21
Internal Temperature -
20 … 100 °C
Temperature of heatsink in
°
C
P0-22
Time Left to next service When 0 => service indicator is led on the display
P0-26
kWh meter 0 to 999,9 When overflow P00-27 increases by 1 and reset to 0.
P0-27
MWh meter 0 to 65535 Displays the amount of energy consumed by the drive.
P0-28
Software Version I/O-version, I/O Checksum, DSP version, DSP checksum.
P0-29
Drive Type Frame size, Power rating and output phases
P0-30
Drive Serial Number Unique drive serial number.
P0-31
Total Run Time 0 to 99999 hours Displays the total operating time of the drive.
P0-35
Fan Run Time 0 to 99999 hours Displays total operating time of internal cooling fans.
P0-36
DC Bus Voltage at Trip V DC Values logged before trip with 8 samples total (256 msec).
P0-37
DC Bus Voltage Ripple at Trip V DC Values logged before trip with 8 samples total (20 msec).
P0-38
Heatsink Temperature at Trip -
20 … 100 °C
Values logged before trip with 8 samples total (30 sec).
P0-39
Ambient Temperature at Trip °C Values logged before trip with 8 samples total (30 sec).
P0-40
Motor Current Log at Trip A Values logged before trip with 8 samples total (256 msec).
P0-41
Over Current Fault Counter Over Current fault counter
P0-42
Over Voltage Fault Counter Over Voltage fault counter
P0-43
Under Voltage Fault Counter Under Voltage fault counter
P0-44
Heatsink Over Temperature Heatsink Over Temperature fault counter
P0-45
Brake Chopper Short Circuit Brake Chopper Short Circuit fault counter
P0-46
Ambient Over Temperature Ambient Over Temperature fault counter
P0-49
Modbus RTU / BACnet Modbus RTU/BACnet communication fault counter
P0-58
Load Torque Profile Current
Values
A
5 Autotuned values of Load Torque Characteristic function.
First display
–Current at minimum speed
Second display
–Current at first measurement interval
Third display
–Current at second measurement interval
Fourth display
–Current at third measurement interval
Fifth display
–Current at maximum speed
P0-64
Switching Frequency kHz Displays the actual effective Switching frequency
P0-65
Drive Life Time Powered up time, hours, min, and sec
P0-70
Option Module ID-code Identifies Type of Option Module in option module slot
P0-71
Fieldbus module ID Fieldbus module Identification Code