Bedrock AM100 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 119

background image

12

Bedrock AM100 operating manual

© Bedrock Audio BV, 2021

13

5. Getting started

You will most likely receive your Bedrock AM100 with sufficiently charged batteries to start
the device and get acquainted with its features. We do recommend that you fully charge
the device before you begin your first serious measurement session.

Leave the device on

the charger until it finishes its charge cycle.

This may take up to 6 hours; many users opt

for overnight charging. It is normal for the device to noticeably warm up during charging.

All rechargeable batteries slowly lose charge during storage, the batteries in
the Bedrock AM100 are no exception. When you take out the device after
it has been on the shelf for more than a few weeks, always fully charge the
batteries first. The battery charge indicator may not be accurate after longer
periods of storage.

5.1. Preparing and booting the AM100

Connect the microphone using the XLR connector at the top of the device. Optionally, for
sensititive measurements, mount the rubber diffuser ring to reduce reflections off of the top
of the AM100. Next, power on the device by pressing the red power button once.

Note: the power button is also used to power the device off. If you press the button while
the device is in operation, you will see a dialog window asking confirmation. If the power
button is kept pressed for 10 seconds in the “power on” state, the device will be forced into
the “off ” condition. This can be used to reset the device if it becomes unresponsive.

5.2. The AM100 main menu

The Bedrock AM100 will boot into the main menu. You can launch its various measure-
ment modules from this menu.

The main menu is where all the available modules are shown, and where you can choose
which module to launch. New modules are regularly added through firmware updates
that are made available through the Bedrock website. If your device is running a different
firmware version than the version on which this manual is based (version 3.0), you may see
a different selection of modules appear in the menu than the ones found in this manual.

«
...
11
12
13
14
15
...
»

Содержание AM100
























































































































Отзывы:

Нет отзывов

Похожие инструкции для AM100

IEM-100 Beltpack

Бренд: DAPAudio Страницы: 19

Бренд: Hammond Страницы: 130

Бренд: TA Instruments Страницы: 7

Бренд: Sensia Страницы: 16

Бренд: LumaSense Страницы: 23

Бренд: Keysight Страницы: 56

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: LORECa Hearing Instrument Страницы: 43

Бренд: HTC Страницы: 2

Бренд: Agilent Technologies Страницы: 26

Бренд: Alcor System Страницы: 21

Бренд: Zamel Страницы: 2

Бренд: LaserLine Страницы: 15

Бренд: hager Страницы: 4

SEC2000 Spectra System

Бренд: BAS Страницы: 66

Sensus 412 Series

Бренд: Xylem Страницы: 13

Бренд: Sfere Страницы: 22

Бренд: Hach Страницы: 414

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды