Bedrock AM100 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 119

background image

10

Bedrock AM100 operating manual

© Bedrock Audio BV, 2021

11

4. General use and safety precautions

Your Bedrock AM100 is a sophisticated electronic measuring instrument that should be
used, maintained and stored with care:

•

If you use a tripod to mount the device during measurements, we recom-
mend that you use a sturdy model with a sufficiently wide base.

•

Do not expose the device itself, the measuring microphone or charger to
rain, moisture or liquids of any kind. Take special care to prevent liquids to
permeate into the device through the connectors or along the display bezel.

•

Do not operate or charge at ambient temperatures above 35

o

C/95F.

•

Do not use close to flames or open fire.

•

Do not use in environments where flammable or explosive materials may
also be used.

•

Do not attempt to charge at ambient temperatures above 35

o

C/95F or below

8

o

C/46F. The AM100 will block charging at these temperatures to prevent

damage to the NiMH battery cells.

•

Use the charger only with the international adapter suitable for your region.

•

Make sure that the device is switched off before transportation and storage.

•

During transportation and storage, keep the device in a suitable casing or
container – preferably its original case. The device needs to be protected
from shocks and vibration (due to transportation or falling), excessive tem-
peratures, liquids and moisture, and any other external conditions that
could do damage to the device. Care should be taken that other objects can-
not come into direct contact with the display during transportation.

4.1. Safety precautions when charging

The Bedrock AM100 is a battery-powered rechargeable device, with an internal low self-
discharge NiMH battery pack. This battery pack is designed for many years of operation,
and therefore cannot be swapped out by the user. Recharging takes place through the mini
USB connector found on the left side of the device.

The device is charged through the USB connector using high currents of
up to 2100 mA. While being charged, it will heat up. DO NOT CHARGE
THE DEVICE WHILE IT IS INSIDE A CLOSED CONTAINER (BOX,
BRIEFCASE, ETC.). Please make sure that the device can shed excess heat
while charging.

«
...
9
10
11
12
13
...
»

Содержание AM100
























































































































Отзывы:

Нет отзывов

Похожие инструкции для AM100

Бренд: DAKOTA ULTRASONICS Страницы: 48

Бренд: TE Connectivity Страницы: 9

SMatrix DMX2400

Бренд: dallmeier Страницы: 12

Бренд: Hardy Barth Страницы: 27

Бренд: Yamaha Страницы: 84

Бренд: M-Sure Страницы: 2

Бренд: Dräger Страницы: 538

Бренд: DODODUCK Страницы: 2

Бренд: Spasciani Страницы: 26

Бренд: Ramsey Electronics Страницы: 40

Бренд: IDT Страницы: 20

Бренд: R&S Страницы: 130

Бренд: Eno Scientific Страницы: 47

Бренд: Chauvin Arnoux Страницы: 44

Бренд: Droplet Страницы: 35

Бренд: Sencore Страницы: 75

Бренд: truflo Страницы: 33

Бренд: Vega Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды