Beckhoff EPP6228-0022, Руководство пользователя

Страница: 66 / 79

Diagnosis
EPP6228-0022 66 Version: 1.3
ErrorTypes (IO-Link Spec)
Incident Error
Code Additional
Code Name Definition
Device application
error – no details 0x80 0x00 APP_DEV This ErrorType shall be used if the requested service has
been refused by the Device application and no detailed
Index not avail-
able 0x80 0x11 IDX_NOTAVAIL This ErrorType shall be used whenever a read or write
access occurs to a not existing Index.
Subindex not
available 0x80 0x12 SUBIDX_NOTAVAIL This ErrorType shall be used whenever a read or write
access occurs to a not existing Subindex.
Service temporar-
ily not available 0x80 0x20 SERV_NOTAVAIL This ErrorType shall be used if a parameter is not acces-
sible for a read or write service due to the current state of
the Device application.
Service temporar-
ily not available –
local control 0x80 0x21 SERV_NOTAVAIL_LOCCTRL This ErrorType shall be used if a parameter is not acces-
sible for a read or write service due to an ongoing local
operation at the Device (for example operation or param-
eterization via an on-board Device control panel).
Service temporar-
ily not available –
Device control 0x80 0x22 SERV_NOTAVAIL_DEVCTRL This ErrorType shall be used if a read or write service is
not accessible due to a remote triggered state of the de-
vice application (for example parameterization during a
remote triggered teach-in operation or calibration).
Access denied 0x80 0x23 IDX_NOT_WRITEABLE This ErrorType shall be used if a write service tries to ac-
cess a read-only parameter.
Parameter value
out of range 0x80 0x30 PAR_VALOUTOFRNG This ErrorType shall be used for a write service to a pa-
rameter outside its permitted range of values.
Parameter value
above limit 0x80 0x31 PAR_VALGTLIM This ErrorType shall be used for a write service to a pa-
rameter above its specified value range.
Parameter value
below limit 0x80 0x32 PAR_VALLTLIM This ErrorType shall be used for a write service to a pa-
rameter below its specified value range.
Parameter length
overrun 0x80 0x33 VAL_LENOVRRUN This ErrorType shall be used when the content of a write
service to a parameter is greater than the parameter
specified length. This ErrorType shall also be used, if a
data object is too large to be processed by the Device
application (for example ISDU buffer restriction).
Parameter length
underrun 0x80 0x34 VAL_LENUNDRUN This ErrorType shall be used when the content of a write
service to a parameter is less than the parameter speci-
fied length (for example write access of an Unsigned16
value to an Unsigned32 parameter).
Function not avail-
able 0x80 0x35 FUNC_NOTAVAIL This ErrorType shall be used for a write service with a
command value not supported by the Device application
(for example a SystemCommand with a value not imple-
mented).
Function tempo-
rarily unavailable 0x80 0x36 FUNC_UNAVAILTEMP This ErrorType shall be used for a write service with a
command value calling a Device function not available
due to the current state of the Device application (for ex-
ample a SystemCommand).
Invalid parameter
set 0x80 0x40 PAR_SETINVALID This ErrorType shall be used if values sent via single pa-
rameter transfer are not consistent with other actual pa-
rameter settings (for example overlapping set points for a
binary data setting
Inconsistent pa-
rameter set 0x80 0x41 PAR_SETINCONSIST This ErrorType shall be used at the termination of a block
parameter transfer with ParamDownloadEnd or Param-
DownloadStore if the plausibility check shows inconsis-
tencies
Application not
ready 0x80 0x82 APP_DEVNOTRDY This ErrorType shall be used if a read or write service is
refused due to a temporarily unavailable application (for
example peripheral controllers during startup).
Vendor specific 0x81 0x00 UNSPECIFIC This ErrorType will be propagated directly to higher level
processing elements as an error (no warning) by the
Master.
Vendor specific 0x81 0x01 to
0xFF VENDOR_SPECIFIC
Table C.1 ErrorTypes, IO-Link Spec