Beckhoff AA3000 Скачать руководство пользователя страница 58

Страница: 58 / 67

Fault correction

───

Version: 1.0

AA3000

Number

Cause

Solution

Servo drive not enabled

Set ENABLE signal and enable servo drive

Motor overload

Check the load and if necessary reduce it, then
restart and enable the servo drive. Set EN-
ABLE signal

Mechanical blockage of the motor

Check mechanics and release blockage

Holding brake [+] not released

Check the control configuration of the holding
brakes [+] and reconfigure if necessary

Phase interruption in the power supply or reversed
motor phases

Check servo drive and supply cables and re-
place any defective cables

Phase interruption after power supply; switching on Check servo drive and supply cables and re-

place any defective cables

Power cable or feedback line with defective shield

Check ground connection and shielding

Short-circuit in the voltage supply cable for the
holding brake [+]

Replace defective cable, measure and check
cable after replacement

Output voltage of the servo drive too low

Check the settings in the configuration and
read out the electronic identification plate of
the motor again

Defective holding brake [+]

Replace motor, then measure and check

Short circuit or earth leakage in the motor line

Replace defective motor line, then measure
and check

Power connector not fitted correctly

Check the connectors on the power connector
and on the motor

Interruption in the feedback or motor line

Check cables for wire break or crushing. Re-
place defective cables, then measure and
check.

Содержание AA3000




































































Результаты поиска

Содержание AA3000

Отзывы:

Похожие инструкции для AA3000

Бренды по названию

Популярные бренды

Beckhoff AA3000, Руководство по эксплуатации

Результаты поиска

Содержание AA3000

Отзывы:

Похожие инструкции для AA3000

Бренды по названию

Популярные бренды