Beast BCR130/5 BG Скачать руководство пользователя страница 8

Страница: 8 / 16

BCR130/5-BCR164/6,5-BCR300/12

BEAST CORE RIG OPERATING MANUAL

Vacuum pump

•

Avoid any constrictions in the suction hose,

e.g. due to dirt accumulation, squeezing,

bending or stretching.

•

Check the suction hose each time before

use. Renew any leaking or damaged parts.

•

Keep the cooling air vents on the pump free

and clean.

•

The underlying surface of the drill stand

must be clean, firm, smooth, dry and with-

out any holes. For further safety regulations,

see the operating instructions for the drill

stand.

•

Caution: The machine automatically

switches on immediately after inserting the

plug in the mains and becomes hot after a

long period of use.

•

Always

connect the core drill and the vac-

uum pump to the same power outlet.

•

Do not carry out any changes or modifica-

tions to the machine.

•

Should the machine have an operational

fault, the vacuum function will remain for a

short time. The cohesion is depe dent upon

the underlying surface and seal retention.

Stop working immediately and remove the

drill stand completely.

Use only original BEAST/B+BTec parts and

accessories.

TOOL SPECIFICATIONS

Drill

BCR130/5 BG

BCR130/5 MG

BCR164/6,5

BCR300/12

Input power (Watt)

2 .000 W

2 .400 W

Motor (Voltage)

110 V

(Frequency/Amps)

50-60 Hz/16 A

50-60 Hz/20A

No-load speed 1-2-3

min

-1

900-2 .180-4 .290 900-2 .180-4 .290 620-1 .400-3 .500 450-900-1 .600

Bore diameter
Wet/Dry 1 . Gear

Ø mm

55-130/55-164

101-164/-

120-300/-

Wet/Dry 2 . Gear

Ø mm

25-60/25-60

41-101/-

60-150/-

Wet/Dry 3 . Gear

Ø mm

8-35/8-35

10-41/-

25-80/-

Dimensions L x B x H

44,5 x 28 x 11,5

44,5 x 30 x 11,5

59 x 20 x 22

60 x 27 x 22

Weight
Motor

7,5 kg*

12,9 kg**

12 kg

Guide block

4,1 kg

3,9 kg

Drill Stand Compact

10,3 kg

Drill Stand Large

13,9 kg

Safety class (EN-IEC 61029)

/ I

Safety class (IP Code)

IP54

* Drill BCR 130 overall weight . ** Incl . guide block .

Vacuum pump

Rated voltage

110 Volt

Maximum vacuum

-800 mbar

Rated input

500 Watt

Weight

11,2 kg

Содержание BCR130/5 BG

















Результаты поиска

Содержание BCR130/5 BG

Отзывы:

Похожие инструкции для BCR130/5 BG

Бренды по названию

Популярные бренды

Beast BCR130/5 BG, Руководство по эксплуатации

Результаты поиска

Содержание BCR130/5 BG

Отзывы:

Похожие инструкции для BCR130/5 BG

Бренды по названию

Популярные бренды