BEA IXIO-DT3 Скачать руководство пользователя страница 6

2

1

4

6

7

5

1
2

1
2

1
2

1

1

1
2

1
2

1
2

1

1

1
2

1
2

1
2

1

1

1
2

1
2

2

2

6

8

9

2

1

1

E1

E2

E4

E5

E6

E7

E8

E9

TROUBLESHOOTING

The ORANGE LED 
flashes 1 x.

The ORANGE LED 
flashes 2 x.

The ORANGE LED 
flashes 4 x.

The ORANGE LED 
is on.

The RED LED flashes 
quickly after an 
assisted setup.

The RED LED 
lights up 
sporadically.

The GREEN LED 
lights up 
sporadically.

The LED and the 
LCD-display are off.

The reaction of 

the door does not 

correspond to the 

LED-signal.

The sensor signals 
an internal fault.

The power supply is too 
low or too high.

The sensor receives 
not enough AIR-energy.

The sensor encounters 
a memory problem.

The sensor vibrates.

The sensor sees the door 
during the assisted setup.

The sensor sees the door.

The sensor is disturbed 
by external conditions.

The sensor is disturbed by 
rain and/or leaves.

The sensor vibrates.

Ghosting created by door 
movement.

The sensor sees the door 
or other moving objects.

Check power supply 

(in the diagnostics menu of the LCD).

Check wiring.

Check the angle of the AIR-curtains.
Increase the AIR-immunity filter (values >2.8 m).

Cut and restore power supply.  
If orange LED lights up again, replace sensor.

Check the angle of the AIR-curtains.
Launch a new assisted setup.

Attention: Do not stand in the detection field!

Check output configuration setting.
Check wiring.

Check if the sensor is fastened firmly.
Check position of cable and cover.

Increase the AIR-immunity filter to value 3.
Select presetting 2 or 3.

Select presetting 2 or 3. 
Increase radar-immunity filter.

Change radar field angle.

Check if the sensor and door cover is fastened firmly.
Check position of cable and cover.

Change radar field size or angle.

Remove the objects if possible.

Launch an assisted setup and adjust the AIR angle.

Cut and restore power supply.
If orange LED flashes again, replace sensor.

The ORANGE LED 
flashes 6 x.

The ORANGE LED 
flashes 7 x.

The radar sensor output is 
faulty.

Replace sensor.

The internal test of the 
radar is disturbed.

Change radar field angle.
If orange LED flashes again, replace sensor.

Cut and restore power supply.
Check wiring.

The ORANGE LED 
flashes 5 x.

The sensor receives 
too much AIR-energy.

Check the angle of the AIR-curtains.
Decrease the AIR-immunity filter (values 1-3 <2.8 m).

Motion 
detection

Presence 
detection

LED flashes

LED flashes 
quickly

LED is off

The ORANGE LED 
flashes 8 x.

The AIR power emitter is 
faulty.

Replace sensor.

The ORANGE LED 
flashes 9 x.

The internal reference of 
the radar is faulty.

Replace sensor.

Содержание IXIO-DT3









Отзывы: