background image

Colour: Red

Location: Blower Side

Stones or other objects 

may be thrown great 

distances by the auger, 

especially at higher RPM. 

Do not stand in front of

the blower when it is in

operation.

Any debris or stones which are swept into 

the fan can be thrown at great distances.

Do not allow any bystanders to stand in

the oath of the discharge chute.

Shields are supplied for your protection. 

Do not remove shield and do not operate

the machine unless all shields are in place.

Do not service, adjust or repair until the PTO 

has been disengaged, the motor shut off, 

the unit lowered to the ground and all parts

have stopped moving. Any moving part has 

the possibility of entangling the operator or

his clothing and causing serious injury, 

dismemberment or death.

Colour: Red

Location: Blower Side

Colour: Yellow

Location: Blower Back

Do not service, adjust or 

repair any equipment 

attached to the 3PT

hitch hydraulic, without

lowering the unit to the

ground. If work must be

performed underneath

the unit, block the unit

in a raised position.

Colour: Orange

Location: Blower Back

Do not attempt any 

servicing of the blower 

while the tractor engine 

is running. If the tractor 

PTO is accidentally 

engaged the serviceman 

could become entangled

in moving parts and

seriously injured or killed.

Be certain. Be safe.

Shut off the engine.

Colour: Yellow

Location: Blower Back

Every effort is made to

ensure that a well

constructed high quality

product leaves the

manufacturer. Again the 

dealer inspects and 

services each unit before

it leaves his lot.

Colour: Orange

Location: Blower Side

Colour: Red

Location: PTO Shaft

Never go near any moving

parts. Because tractor PTO

may be accidentally engaged,

Repair or couple PTO unless 

tractor engine is shut off.

Do not remove shields. 

Be sure that PTO shield turns 

freely and independently of

the driveline. Do not operate

unless all shields are in place.

Be sure that PTO shaft is 

attached securely at both 

ends before operating.

SAFETY DECALS

BE-SBSxxG

To keep your blower in

good operating condition,

please inspect and re-tighten as necessary any loose 

nuts or studs after a half hour break in period. 

Thereafter periodic checks will ensure that your

blower remains in top working condition.

CAUTION

Lower or block elevated components before

servicing or when leaving the machine.

Elevated components can fail and cause

serious injury.

Abaissez ou bloquez les éléments surélevés

avant de faire l’entretien lorsque vous vous

éloignez de la machine. Les éléments 

surélevés peuvent tomber et causer des

blessures sérieuses.

DANGER

Shut off engine before 

servicing machine.

Éteindre le moteur avant

de faire l’entrtien.

CAUTION

All nuts and bolts must be

re-tightened regularly.

Consult your Owners Manual.

Tous les écrous et les boulons

doivent être resserrés à

intervalles réguliers. Consultez

le manuel de l’usager.

DANGER

To prevent Serious Injury or Death:

 • Keep hands, feet and clothing away 

   from auger intake

WARNING

MOVING PART HAZARD

To prevent serious injury or death from

moving parts:

 • Close and secure guards and shields 

    before starting.

 • Keep hands, feet, hair and clothing away

    from moving parts.

 • Disconnect and lockout power source

    before adjusting or servicing.

 • Do not stand or climb on machine when

    operating.

DANGER

ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH

KEEP AWAY!

DO NOT OPERATE WITHOUT:

• ALL DRIVELINE, TRACTOR AND

  EQUIPMENT SHIELDS IN PLACE
• DRIVELINES SECURELY

   ATTACHED AT BOTH ENDS
• DRIVELINE SHIELDS THAT TURN

   FREELY ON DRIVELINE

DANGER

AVOID BODILY INJURY

PRÉVENTION CONTRE

LES ACCIDENTS

1. OBJECTS MAY BE THROWN GREAT

    DISTANCES BY AUGER.

    LES OBJETS PEUVENT ÊTRE PROJETER À

    GRANDE DISTANCE DE LA VIS HÉLICOïVALE.

2. STAY CLEAR AND WATCH OUT FOR

    BYSTANDERS. KEEP ALL SHIELDS IN PLACE.

    GARDEZ UNE BONNE DISTANCE ENTRE VOUS

    ET LES PERONNES ENVIRONNANTES.

    N’ENLEVESPAS LA TÔLE PROTECTRICE.

3. BEFORE WORKING ON MACHINE DISENGAGE

    POWER, SHUT OFF ENGINE AND MAKE SURE

    AUGER HAS STOPPED ROTATING.

    AVANT TOUTES RÉPARATIONS, ENLEVEZ LE

    ASSUREZ-VOUS QUE LA VIS HÉLICOïVALE

    NE TOURNE PLUS.

Содержание BE-SBS G Series
















Отзывы: