BDS MABasic 200 Скачать руководство пользователя страница 12

12

MABasic 200, 400, 450, 850,

GB

Use

Select the rotating speed range  

(only MABasic 400, 450 and 850)

ATTENTION

 

Switch the gear stages only with the 

machine at standstill.

NOTE

 

Select the speed range according to 

the material and drilling diameter.

Select the gear stage MABasic 400/450

The machine has a gearbox with two me-

chanical gear stages. The rotation speeds 

of the gear stages are specified in the 

technical data.

 

‹

To select the desired gear stage, 

set selector lever on the gearbox (3) 

to stage 1 or 2 with the machine 

switched off.

Select the gear stage MABasic 850

The machine is equipped with a gearbox 

that has four mechanical gear stages. The 

rotation speeds of the gear stages are 

specified in the technical data.

 

‹

To select the gear stage, switch the 

machine off and set both selector le

-

vers on the gearbox (3) to the desired 

speed according to the table below.

Rotating 

speed 

Selector lever

left

right

Level 1

Level 2

Level 3

Level 4

Activating/deactivating the mag-

netic clamp

Activating the magnetic clamp

ATTENTION

 

To prevent the magnet from overheat-

ing, switch on the magnetic clamp 

only when the machine is standing on 

a magnetic substrate.

 

‹

Turn on the switch (11). The indicator 

lamp in the switch (11) lights up.

ATTENTION

 

The maximum magnetic holding 

force is only available after 

switching on the motor.

Deactivating the magnetic clamp

 

‹

Hold the handle tightly (5) to stop the 

machine from slipping.

 

‹

Turn off the switch (11). The indicator 

lamp in the switch (11) extinguishes.

Switching the machine ON/OFF

 

‹

Using the ON/OFF switch (10), turn 

the machine ON with the green button 

(I) and OFF with the red button (O).

NOTE

 

The machine can only be switched on 

when the magnetic clamp has been 

switched on.

 

Allow a severely overheated machine 

to run on at idle speed for approx. 

2 minutes.

 

The machine switches off automati

-

cally in the event of a power failure or 

if the magnetic clamp is switched off.

use

Содержание MABasic 200





















Отзывы: