BDS MAB 455 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 22

BDS MAB 455 Скачать руководство пользователя страница 9

9

MAB 455

GB

Symbols on the machine

The symbols on the machine have the

following meaning:

Symbol Meaning

Electric shock hazard!

Read the operating instructions

before beginning work!

Wear protective goggles and

ear protection!

Personal protective equipment

Wear the following protective equipment at

all times when operating the machine:

Symbol Meaning

Close-fitting work protection

clothing with a low tear strength

Goggles for protecting eyes

against flying parts and liquids

and ear protection in areas with

noise emission >80 dB(A)

Safety shoes for protecting feet

against falling objects.

Also wear the following protective equip-

ment during special work:

Symbol Meaning

Helmet for protecting your head

against falling objects

Wear a harness where there is

a danger of falling.

Gloves for protection against

injuries

Safety

«
...
7
8
9
10
11
...
»

Содержание MAB 455























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды