background image

LED STATUS LIGHT - LANDLINE

When troubleshooting, the Base Unit has an LED light that indicates its status. The light may display 
the following signals:

LED Light

Steady Red

Short Green Flash 

at periodic 

intervals

Short Red Flash at 

periodic intervals

Short Orange 

Flash at periodic 

intervals

Steady Green

The Base Unit has been 
activated by an alarm 
signal and is trying to call 
the response center.

AC power is not
available and the Base 
Unit is being powered 
from its internal backup 
battery

The Base Unit is not 
connected to an 
operating telephone line.

Let the Base Unit complete the call, do not 
try to reset the unit.

Check the power connection

Check the telephone connection between 
the Base Unit and the wall jack in your 
home.

The Base Unit is being 
powered by its internal 
backup battery, and the 
Base Unit is not 
connected to an 
operating telephone line.

Check the telephone connection between 
the Medical Alert Unit and the wall jack in 
your home.  

Also check the power connection. 

The Base Unit is properly 
plugged in to AC power 
and a telephone line, and 
is ready to call the 
monitoring center

No action needed.

What It Means

What You Should Do

4

Содержание In-Home System











Отзывы: