background image

8

925.220.4 - EN

INSTRUCTIONS PERTAINING TO THE USER

Summary table of available groups of days 

'"$503:4&55*/(4

Group “MO-FR”

%":

from Monday to Friday

As per table in paragraph 3.6.1.

Group “SA-SU”

%":

Saturday and Sunday

07:00 – 23:00

Group “MO-SA”

%":

from Monday to Saturday

As per table in paragraph 3.6.1.

Group “MO-SU”

%":

every day of the week

 

As per table in paragraph 3.6.1.

3.7 PROGRAMMING DHW MODE OPERATION TIMES

(only for boilers connected to

 

an external heater)

This function enables the programming of

 

four boiler DHW mode 

operation time slots

 

in the span of a week

 

(the programmed time slots 

are the same for every day of the week).

To set the programming of DHW mode operation times

proceed as 

follows

:

1)

 Press the 

IP

 button and then the button 

 to enter the 

programming (heating and DHW modes);

2)

  Select the DHW programme “

HW PR

” by repeatedly pressing the 

buttons 

+/-

 

;

0607_1905

3)

 Press the 

OK

 button

4)

  Set the time slots in which you can enable

 

DHW mode operation

 

by repeating the operations described in points 4-10 

of paragraph 3.6.1 (factory setting 06:00 - 23:00). 

IMPORTANT:

   the installer has to set “

HW PR

” parameter = 

2

, as described in section 19.1.

0609_1602

Programming in DHW 

MODE 

PROGRAMMED TIME BAND

09:00 - 12:00

Days of the week

Содержание LUNA3COMFORT











































Отзывы: