Baxi Bermuda PW5 C5 Скачать руководство пользователя страница 5

Страница: 5 / 16

page 5

Fitting the Fire

Bend the central flap of the backing plate and the two

securing brackets as shown in the diagram.

Fit the fire backing plate to the fire using the M5 x 8mm
thread forming screws provided (Fig.5).

Fit the extension panel supplied with the fire to the boiler
controls heat shield using two of the No. 8 x

in. self

tapping screws (Fig.4).

IMPORTANT: The extension panel MUST be fitted.

HEARTH FIXING

1. Locate the fire spigot into the draught diverter on the
boiler. Push the fire backwards until the backing plate
touches the surround or finished wall face. Adjust the feet
to level the fire (Fig.5).

2. Mark the position of the most suitable pair of securing
holes in the fire backing plate (Fig.5) and remove the fire.
Drill and plug the wall with suitable plugs. Replace the fire
and secure to the wall with suitable fixing screws.

3. Connect the supply pipe to the fire inlet connection.

WALL FIXING

1. Slide the fire support plate over the overhanging boiler
base (Fig.4). Using the screws provided, loosely attach
the plate using the slots at each side.

2. On electronic control boilers it will be necessary to
disconnect the input plug from the controls. Push the
support plate backwards until it touches the wall surface
and tighten the screws to lock the frame in position.
Locate the fire spigot into the draught diverter on the
boiler. Push the fire backwards until the backing plate
touches the finished wall face. Adjust the feet to level the
fire (Fig 5).

3. Mark the position of the most suitable pair of securing
holes in the fire backing plate (Fig.5) and remove the fire.
Drill and plug the wall with suitable plugs. Replace the fire
and secure to the wall with suitable fixing screws .

4. Connect the gas supply pipe to the fire inlet connection.

Surround Face or
Finished Wall Face

Front "V" Mark

Gas Service Tap

560mm

(22in)

406-584mm

(16-23in)

PW5 991mm Min.

C5 & C5W 860mm Min.

PW5 991mm Min.

C5 & C5W 860mm Min.

If the opening is being purposely prepared the maximum dimensions are

strongly recommended

Fig. 1 Fireplace Opening

560mm

(22in)

406-584mm

(16-23in)

Fig. 2 Wall Fixing

Maximum

dimensions are

strongly

recommended

Fig. 3 Gas Supply Pipe

Fireplace

Opening

Fireplace

Opening

Skirting Board

Hearth
Level

100-125mm

(4-5in)

Fig. 4 Wall Fixing - Support Plate

Fire Support
Plate

Controls Heat
Shield

Gas Service
Tap

Appliance Details

ERMUDA

PW5 Deluxe

Height - 637mm (to hearth)

(see page 7

Width - 832mm

for clearances)

Depth - 206mm

ERMUDA

C5/C5W

Height - C5 639mm (to hearth)

C5W 654mm (to hearth)

(see page 7

Width - 720mm

for clearances)

Depth - 201mm

EAT

NPUT

(

GROSS

)

4.67kW (15,900 Btu/h)

ROUP

G20 (Natural Gas)

NJECTOR

IZE

170S (PW5Deluxe)
C06 (C5 & C5W)

ETTING

RESSURE

(Cold) 17.2+1 mbar (6.9+ 0.4 in wg)

HERMOCOUPLE

UTPUT

7.5 - 13mV

ILOT

SSY

21100/165

EAT

NPUT

(

GROSS

)

210W (715 Btu/h)

Extension
Panel

675mm Min.

(26

in) C5W

660mm Min.

(26in) PW5 &C5

675mm Min.

(26

in) C5W

660mm Min.

(26in) PW5 &C5

Backing Plate

Содержание Bermuda PW5 C5

















Результаты поиска

Содержание Bermuda PW5 C5

Отзывы:

Бренды по названию

Популярные бренды

Baxi Bermuda PW5 C5, Инструкции по установке и обслуживанию

Результаты поиска

Содержание Bermuda PW5 C5

Отзывы:

Бренды по названию

Популярные бренды