Baumuller DS 100 Скачать руководство пользователя страница 8

Страница: 8 / 23

TAM 00624

DS 100 – 200

03 / 2005

Three-phase synchronous motor, air-cooled

English

Electrical connections (comp.

Appendix 1

)

Main connection

Terminal box

Control connection

Resolver - 12-pole connector

Fan / built-in fan motor

6-pin connector

(unit DA 100)

Fan / added-on standard motor

Terminal box, standard motor (unit DA 132 -280)

Brake (optional)

Separate connection

Thermal sensor

Connection in terminal box

Thermal motor protection (EN60034-11)

Thermal sensor KTY84 in stator winding

Winding insulation (EN 60034-1)

Insulation class F

Ambient temperature

0°C ... +40°C

Installation (EN 60034-1)

= 1.000 m a.m.s.l.

Storage

-30°C…+60°C (+ 85°C,

comp. Chap. 2.5

)

Bearing

Rolling-contact bearing with grease lubrication for life

Calculated bearing life

20.000h (tentative value)

Vibration severity (EN 60034-14)

Level N

Vibration-resistant to … (to EN 60068-2-6)

Radial 3g (20Hz to 55 Hz)

Axial 0.5g (20Hz to 55 Hz)

Holding brake

Option

Actual speed encoder

Standard:

2-pole

Resolver

For further technical values, please refer to the technical documentation that comes with the
product.

Attention!

If the electric motor supplied is not a standard version in accordance with the technical

documentation or if special arrangements were contractually agreed, the technical data may differ
to the values stated in these Commissioning and Maintenance Instructions. The supplementary
technical details are available on request.

Содержание DS 100
























Результаты поиска

Содержание DS 100

Отзывы:

Похожие инструкции для DS 100

Бренды по названию

Популярные бренды

Baumuller DS 100, Инструкции по вводу в эксплуатацию и техническому обслуживанию

Результаты поиска

Содержание DS 100

Отзывы:

Похожие инструкции для DS 100

Бренды по названию

Популярные бренды