Baumer VisiLine Скачать руководство пользователя страница 10

Страница: 10 / 68

Installation

Lens mounting

Notice

Avoid contamination of the sensor and the lens by dust and airborne particles when

mounting the support or the lens to the device!
Therefore the following points are very important:

Install the camera in an environment that is as dust free as possible!

▪

Keep the dust cover (bag) on camera as long as possible!

▪

Hold the print with the sensor downwards with unprotected sensor.

▪

Avoid contact with any optical surface of the camera!

▪

Environmental Requirements

6.1

Temperature

Storage temperature

-10°C ... +70°C ( +14°F ... +158°F)

Operating temperature*

see Heat Transmission

* If the environmental temperature exceeds the values listed in the table below, the cam-

era must be cooled. (see Heat Transmission)

Humidity

Storage and Operating Humidity

10% ... 90%

Non-condensing

Heat Transmission

6.2

Caution

Heat can damage the camera. Provide adequate dissipation of heat, to

ensure that the temperature does not exceed 50°C (122°F).

As there are numerous possibilities for installation, Baumer does not

specify a specific method for proper heat dissipation.

Measure Point

Maximal Temperature

50°C (122°F)

Figure 2 ►

Temperature measuring
point

Содержание VisiLine





































































Результаты поиска

Содержание VisiLine

Отзывы:

Бренды по названию

Популярные бренды

Baumer VisiLine, Руководство пользователя

Результаты поиска

Содержание VisiLine

Отзывы:

Бренды по названию

Популярные бренды