Baumer MAGRES BMMS M75 Скачать руководство пользователя страница 8

Страница: 8 / 20

Manual_BMMS_CANopen_BECH_EN_rev05.docx

8/20

Baumer Electric AG

18.06.2013

Frauenfeld, Switzerland

3.5

Difference between

absolute encoder with cable-pull

and

absolute encoder redundant

with cable-pull

The

absolute encoder with cable-pull

system implements the functions for an absolute linear encoder system.

The a

bsolute encoder redundant with cable-pull

system extends these functions with a second position from a second

position acquisition. There is also the possibility to monitor the difference between these two positions.

The

absolute encoder redundant with cable-pull

pull is fully compatible to the

absolute encoder with cable-pull

4 NMT Service

4.1

Supported commands

Following NMT commands are supported:



NMT Start



NMT Preoperational



NMT Stop



NMT Reset



NMT Communication Reset

There is no difference between NMT Reset and NMT Communication Reset

4.2

Boot up message

After a power-on or NMT reset, the device will send a Boot up message.

COB ID

Byte 0

700h + node ID

Содержание MAGRES BMMS M75





















Результаты поиска

Содержание MAGRES BMMS M75

Отзывы:

Похожие инструкции для MAGRES BMMS M75

Бренды по названию

Популярные бренды

Baumer MAGRES BMMS M75, Руководство пользователя

Результаты поиска

Содержание MAGRES BMMS M75

Отзывы:

Похожие инструкции для MAGRES BMMS M75

Бренды по названию

Популярные бренды