Baumer MAGRES BMMS M75 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 20

background image

Manual_BMMS_CANopen_BECH_EN_rev05.docx

16/20

Baumer Electric AG

18.06.2013

Frauenfeld, Switzerland

10 LSS slave

10.1 General

The baud rate and node ID can be configured by LSS (according to CiA 305). Another possibility to change the baud rate

and node ID is to access to the objects 2100h and 2101h (see object directory).

The LSS service is only available in NMT Stopped Mode.

10.2 Supported commands



Switch state global



Switch state selective



Configure node ID protocol



Configure bit timing parameters



Store configuration



Inquire identity vendor-ID



Inquire identity product code



Inquire identity revision number



Inquire identity serial number



Inquire identity node ID

10.3 LSS address

The needed values for LSS addressing as vendor ID, revision number, product code and serial number are printed on a

label on the encoder housing.

«
...
14
15
16
17
18
...
»

Содержание MAGRES BMMS M75





















Отзывы:

Нет отзывов

Похожие инструкции для MAGRES BMMS M75

Бренд: Omega Engineering Страницы: 10

Бренд: Parkside Страницы: 77

Бренд: Parkside Страницы: 65

Бренд: Lenze Страницы: 132

Бренд: Midian Страницы: 28

Бренд: Datavideo Страницы: 13

Бренд: B&B Electronics Страницы: 2

Giga-McBasic II

Бренд: B&B Страницы: 2

Бренд: ViewSonic Страницы: 26

Бренд: Silicon Solar Страницы: 3

Бренд: Tektronix Страницы: 43

Бренд: Daewoo Страницы: 16

Бренд: Black Box Страницы: 23

Бренд: Micronix Страницы: 16

Бренд: Moxa Technologies Страницы: 2

7100 Series Power Center

Бренд: Parallax Power Supply Страницы: 2

CSI-5K-S22003-E

Бренд: CanadianSolar Страницы: 29

Бренд: Zipper Mowers Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды