background image

 

22

Minimum flow adjustment for the hob gas tap. 

 
All  work  must  be  carried  out  by  a  GASSAFE 
registered engineer. 
 

 
IMPORTANT: Always isolate the hob from the electricity supply 
before changing the injectors and/or adjusting the minimum 
flow of the burners. 
 

o

 

Switch the burner on 
and set the knob at the 
minimum position. 

 

o

 

Remove the knob from 
the tap and place a 
small bladed 
screwdriver in the 
centre of the tap shaft. 

 
 
 
 
 

 

o

 

Unscrew the adjusting screw, in order to increase the gas flow or 
tighten the adjusting screw to decrease the gas flow. 

 

o

 

The correct adjustment is obtained when the flame has a 
length of about 3 – 4 mm. 

 

o

 

For butane/propane gas, the adjusting screw must be tightly 
screwed in. 

 

o

 

Refit the control knob. 

 

o

 

Make sure that the flame does not go out by quickly turning 
from maximum flow to minimum flow. If it does then remove 
the control knob and make further adjustments to the gas 
flow, testing it again once the adjustment has been made. 

 

o

 

Repeat this process for each one of the gas taps. 

 
 
 
 
 
 
 

Содержание BHG340SS





























Отзывы: