Bauer RAINSTAR A1 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 35

Bauer RAINSTAR A1 Скачать руководство пользователя страница 27

Manual for

BAUER RAINSTAR A1, A2

23

14 SETTING THE GEARBOX SHUT-OFF DEVICE

Push a chock (K) into the gap between tripod lift and bracing (23) which can be found on the drive side behind
the tripod lift (21).

1. Adjusting the shut-off of the gear drive

Click the tripod hook into place and add a distance of 4mm; unscrew the bolt (13) until the gear drive shuts off.
The moment when the gear drive disconnects can be determined best by using the hand wheel and pretension
approximately 5 to 10 kg by hand. As soon as the gear drive disconnects the hand wheel resets. Pretension can
also be reached with a weight.

2.Adjusting the set screw

Adjust the set screw (11) and leave 7mm gap to the tripod lift. There is still a distance of 4mm between tripod
hook (10) and bolt

3.Adjusting the brake

Click the brake handle into place (minor brake force – belt brake spring length 29 mm); and then click the tripod
lift hook into place with a 2mm distance. Unscrew the bolt (15) until the brake handle is unlocked and skips
forward. Please be aware that when turning the bolt it is in one line with the borehole, otherwise the adjustment
changes when the bolt is tightened.
Secure the bolts. After adjusting the shut-off, remove the chock (K) again.

The shut-off frame (17) is set with a distance of

X

mm to the reel (18) (see table).

Adjust screw (19) to the shut-off device (20), lock with nut.
Drive in dowel pin (

22

) at the value of "Y" until it supports at the console on the frame.

Machine

X

mm

Y

mm

RAINSTAR A1, A2

25

80

X

Y

2 / 4

6

18

17

19

22

20

21

13

15

16

11

10

K

14

23

«
...
25
26
27
28
29
...
»

Содержание RAINSTAR A1




































Отзывы:

Нет отзывов