background image

Page 11

For technical questions, please call 1-888-866-5797.

Item 59365 

        

Sa

Fety

Opera

ti

O

n

Maintenance

Setup

Battery charging

Charge battery pack before using this tool.  Follow instructions included 

with battery charger.  Battery Pack and Charger sold separately.

installing the Battery pack

note:

  Battery Pack sold separately.

1.  With the ON/OFF Switch in the “OFF” position, 

insert a fully charged battery pack into the 

Battery Receptacle until it clicks in place.

2. 

to remove

, push the latch on the 

battery back and slide it out.

Latch

Battery pack

Battery 

receptacle

Workpiece and Work area Set up

1.  Designate a work area that is clean and well‑lit.  

The work area must not allow access by children 

or pets to prevent distraction and injury.

2.  Secure loose workpieces using a vise or clamps 

(not included) to prevent movement while working.

3.  There must not be hazardous objects, such 

as utility lines or foreign objects, nearby 

that will present a hazard while working.

4.  You must use personal safety equipment including, 

but not limited to, ANSI‑approved eye and hearing 

protection, as well as heavy‑duty work gloves.

5.  Before beginning work, provide for sparks 

and debris that will fly off the work surface.

Содержание 2269C-B

















Отзывы: