Bauer 2161CR-B Скачать руководство пользователя

Страница: 17 / 20

Page 17

For technical questions, please call 1-888-866-5797.

Item 58308

FETY

OPERA

MAINTENANCE

SETUP

Troubleshooting

Problem

Possible Causes

Likely Solutions

Tool will not start.

1. Battery Pack not properly connected.

2. Battery Pack not properly charged.

3. Battery Pack worn.

4. Tool’s thermal reset

breaker tripped

(if equipped).

5. Internal damage or wear.

(Switch, for example.)

1. Remove Battery Pack, make sure there

are no obstructions, reinsert the Battery

Pack according to its shape (it should

only fit one way), and press firmly until

the Battery Pack locks in place.

2. Make sure Charger is connected and

operating properly. Give enough time

for Battery Pack to recharge properly.

3. Dispose of old Battery Pack

properly or recycle. Replace Battery Pack.

4. Turn off tool and allow to cool.

Press reset button on tool.

5. Have technician service tool.

Tool operates slowly. 1. Excess pressure applied to workpiece.

2. Battery Pack power low.
3. Battery Pack worn.

1.  Decrease pressure, allow tool to do the work.
2.  Recharge Battery Pack.
3.  Dispose of old Battery Pack

properly or recycle. Replace Battery Pack.

Performance

decreases over time.

Battery Pack wearing out.

Battery Pack capacity will gradually

decrease through use. If symptoms

are severe, recycle old Battery Pack

(or dispose of properly) and replace it.

Excessive noise

or rattling.

Internal damage or wear.

(Bearings, for example.)

Have technician service tool.

Overheating.

1. Forcing tool to work too fast.
2. Blocked motor housing vents.

1. Allow tool to work at its own rate.
2. Wear ANSI-approved safety goggles

and NIOSH-approved dust mask/

respirator while blowing dust out of

motor using compressed air.

Tool does not

operate effectively.

1. Accessory loose.

2. Accessory damaged, worn or

wrong type for the material.

1. Confirm accessory arbor is correct and

Outer Flange/Arbor Nut is tight.

2. Check condition and type of disc accessory.

Use only proper type of disc

accessory in good condition.

Follow all safety precautions whenever diagnosing or servicing

the tool. Disconnect power supply before service.

Содержание 2161CR-B





















Результаты поиска

Содержание 2161CR-B

Отзывы:

Похожие инструкции для 2161CR-B

Бренды по названию

Популярные бренды

Bauer 2161CR-B, Руководство пользователя и инструкции по безопасности

Результаты поиска

Содержание 2161CR-B

Отзывы:

Похожие инструкции для 2161CR-B

Бренды по названию

Популярные бренды