Basler BE1-50/51B-229 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 57

background image

1-2

BE1-50/51B-229 General Information

9252000892 Rev A

APPLICATION

The BE1-50/51B-229 has a wide range of pickup settings and front panel selectable time characteristics.
This makes the relay compatible with applications involving coordination with fuses, reclosers, cold-load
pickup, motor starting, and fixed time requirements. Two switch-selectable reset functions are provided:
instantaneous and integrating. The instantaneous reset function avoids ratcheting. The integrating reset
function simulates the disk reset characteristic of electromechanical relays.

SPECIFICATIONS

BE1-50/51B-229 electrical and physical specifications are listed in the following paragraphs.

Current Sensing Input

Nominal Rating:

5 Aac

Continuous Rating:

14 Aac

One-Second Rating:

400 Aac

Time Overcurrent (51) Element

Setting the TIME PICKUP control at the minimum pickup setting places the relay in the most sensitive
state and may be used as a safety setting.

Pickup

Setting Range:

0.5 to 15.9 Aac

Setting Increment:

0.1 Aac

Accuracy:

±

2%,

±

25 mAac at or above 0.5 Aac setting

Dropout

Dropout occurs at 95% of pickup value.

Timing Range

0.0 to 9.9 seconds in 0.1 second steps.

Timing Accuracy

The timing accuracy is the sum of

±

1 cycle,

±

2 percent over the range of 1.3 to 40 times tap. This

accuracy is for a given measured multiple of tap. The measurement of the multiple of tap has an accuracy
that is the sum of

±

2 percent,

±

25 milliamperes.

Timing Accuracy Example

Pickup Setting:

5 Aac

Current Applied:

6.5 Aac

+Multiple Tolerance:

6.655 Aac

−

Multiple Tolerance:

6.345 Aac

Time Curve:

E

Time Dial:

5.0

Minimum Time (6.655 Aac):

46.5470 sec

Maximum Time (6.345 Aac):

61.3968 sec

Curve Time (6.5 Aac):

53.1800 sec

Curve Characteristics

Nine inverse time functions and one fixed time function can be selected by the front-panel Curve switch.
Characteristic curves for the inverse and definite time functions are defined by the following equation.

Where: T

T

=

time to trip in seconds

D =

time dial setting

M =

multiple of pickup setting

A, B, C, N, K =

constants for the particular curve

Time characteristic curve constants are listed in Tables 1-2 and 1-3. Constants have been selected to
conform to the characteristics of electromechanical relays over a range of pickup multiples from 1.3 to 40.
Values of the constants are provided for use in computer relay setting software. Timing accuracy is

±

1

cycle,

±

2 percent of time to trip.

K

BD

C

M

AD

T

N

T

+

+

=

-

«
...
10
11
12
13
14
...
»

Содержание BE1-50/51B-229


























































Отзывы:

Нет отзывов

Похожие инструкции для BE1-50/51B-229

Бренд: Elko Страницы: 2

Бренд: GE Страницы: 22

Бренд: Philio Страницы: 5

Бренд: hager Страницы: 6

Бренд: Salus Страницы: 4

Бренд: Acces Страницы: 22

Бренд: Eaton Страницы: 112

Бренд: ABB Страницы: 11

Бренд: Zamel Страницы: 2

Бренд: HANYOUNGNUX Страницы: 2

Бренд: Dossena Страницы: 4

Бренд: Aiphone Страницы: 4

Бренд: Tense Страницы: 2

Бренд: Tense Страницы: 2

Бренд: TopflyTech Страницы: 8

Бренд: Pilz Страницы: 32

Бренд: Intiel Страницы: 3

Бренд: DINA Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды