BASF EXACTUS Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 67

background image

-48-

Example 2:

Command the pyrometer to exit Modbus Mode and enter

Exactus

Mode

Field Name

Hex

--------------------------------
Slave Address

01

Function

05

Coil Address Hi 00
Coil Address Lo 13
Force Data Hi

00

Force Data Lo

00

CRC Hi

3C

CRC Lo

0F

Note:

After issuing this command, there will be no response because the pyrometer will enter Exactus Mode

immediately.

Duplex

Full

Parity

None

Data Bits

8

Stop Bits

1

Supported
Baud Rates

9600,
19200,
38400,
57600,
115200,
230400

Modbus
Device
Address

0-255, (set
to 1 at
factory)

Table 2:

Modbus Protocol Serial Settings

NOTE:

See the Modbus Protocol Appendix for a full description of how to use the pyrometer in Modbus Mode.

Exactus

Protocol

The

Exactus

Protocol transmits readings continuously in a binary format at a rate set by the user

in the Temperature software. In this communication mode, the host can send commands to the
pyrometer to start and stop sending readings, or to change operational parameters of the
pyrometer such as the readings data type and transmit frequency.

Data Packet Format

The pyrometer can transmit the following four types of data packets: Temperature, Photodiode
Current, Dual (Temperature and Current), and Ambient Temperature. The data values are
represented within the packets by 4 bytes which represent a 32-bit IEEE-754 floating point
number. The IEEE-754 format is described at the end of this document for the user’s reference.

Exactus

Protocol data messages transmitted by the pyrometer always begin with a Data Message Header byte which

is followed by one or two floating point values.  There is no LRC or other error checking character in the message.
An escape sequence character (0x80) is sent whenever reserved values occur in the data packet values.   The
reserved characters include the packet header bytes, 0x81-0x85, and the ESC value, 0x80.

«
...
50
51
52
53
54
...
»

Содержание EXACTUS




































































Отзывы:

Нет отзывов

Похожие инструкции для EXACTUS

Бренд: Daga Страницы: 38

Бренд: LEGRAND Страницы: 3

Бренд: Danfoss Страницы: 84

Бренд: Robur Страницы: 28

Бренд: CTC Union Страницы: 19

Бренд: Milwaukee Страницы: 48

Бренд: Digi-Sense Страницы: 8

Бренд: Würth Страницы: 36

Бренд: domat Страницы: 8

Бренд: La Crosse Страницы: 2

Бренд: Time Guard Страницы: 5

Бренд: TIGEX Страницы: 3

Бренд: Medisana Страницы: 170

Бренд: Lilytech Страницы: 4

Бренд: Bryant Страницы: 8

DUAL FUEL THERMOSTAT TSTAT

Бренд: Bryant Страницы: 8

Бренд: Bryant Страницы: 28

Бренд: ensto Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды