Bartec SILASPZ Скачать руководство пользователя

Страница: 83 / 90

Maintenance and care

Ex p Control unit

SILAS

Page 82 of 88

A1-37S2-7D0001_pz_Manual_Exp-Control-Unit_20210923_0_en.docx

Rev. 0

Alarm messages

Status

Code

Plain text

0000000D

Ex p inactive

The protected device is deactivated.

0000000E

Device fault 1

HW test error (processors)

0000000F

Device fault 2

HW test error (barriers)

00000010

Device fault 3

HW test error (internal temperature monitoring)

00000011

Device fault 4

HW test error (Fatal)

00000012

Sensor fault

HW test error (pressure sensor / sensor board status)

00000013

Sensor fault

HW test error (opt. current sensors)

00000014

Sensor fault

HW test error (ext. temperature sensors)

00000015

p1 not reached

The set point p1 “Min pressure” has not been reached.

00000016

p3 not reached

The set point p3 “Purging pressure” has not been reached.

00000017

p4 exceeded

The set point p4 “Maximum pressure – operation” is exceeded

00000018

p5 exceeded

The set point p5 “Maximum pressure – Purging” is exceeded.

00000019

Temperature sensor 1 exceeded

The set point temperature value at sensor 1 is exceeded.

0000001A

Temperature sensor 2 exceeded

The set point temperature value at sensor 2 is exceeded.

0000001B

Temperature sensor 3 exceeded

The set point temperature value at sensor 3 is exceeded.

Содержание SILASPZ



























































































Результаты поиска

Содержание SILASPZ

Отзывы:

Похожие инструкции для SILASPZ

Бренды по названию

Популярные бренды

Bartec SILASPZ, Руководство пользователя

Результаты поиска

Содержание SILASPZ

Отзывы:

Похожие инструкции для SILASPZ

Бренды по названию

Популярные бренды