User’s Manual for
1.01 Cubic Ft White Keypad Jewelry Safe
WARNING
Read all instructions before using this safe.
- For security purposes, change the factory default
code as soon as possible. Factory default code
is
168 and 12345678
-Test registered pin code a few times before closing
the safe door.
- Avoid leaving door open and unattended; it will allow
unauthorized individuals to reprogram the safe,
gaining full access to the safe and its contents.
- Body of safe consists of two steel plates filled with a
fire-retardant material
- Do NOT store combustible materials in this unit.
- In the event of a fire, we recommend caution when
opening the safe. If you feel unsure about opening the
safe because of the contents stored, contact your
local fire department for assistance.
- Store emergency keys in a secure place; NOT inside
of the safe.
- Keep children away from safe; they should not play
with or around the safe at anytime. Children at play
could accidentally get locked inside the safe or
accidentally pull on the safe door causing safe to tip
over if not properly mounted.
- Failure to follow these warnings could result in serious
injury or death.
NOTE: BARSKA is not responsible for any damage or
lost contents in the safe due to moisture.
NOTE: BARSKA is not responsible if the safe is stolen
or contents in the safe.
See reverse side for more information
D
Loc
k
U
n
lo
ck
D
E
BATTERY & KEY ACCESS
Push down on button
located under the key pad
and turn keypad cover
counter clockwise.
DO NOT pull on the wires or touch
the electronic components.
Install Battery
Insert one new 9V alkaline battery into the battery compartment
and restore keypad cover.
Key Access
Insert access key into key slot and turn clockwise to open safe.
MOTION SENSOR LIGHT
1. Motion Sensor Light has magnet bar at rear, so it can attach
on the interior surface of safe. Before you start to use safe,
please remove the light from safe and install with 4
AAA batteries.
PARTS OF THE SAFE
A
B
F
5/19
BC607
© 2019 BARSKA®
855 Towne Center Drive | Pomona, CA 91767
(t) 888.666.6769 | (f) 909.445.8169 | www.barska.com
A. Initialization Button
B. Bolts
C. Handle
D. Indicator Lights
F. Motion Sensor Light
F. Keypad and Keypad Cover
- turn keypad counter clock
wise to expose Battery
Compartment and
Emergency Key Access
2. Motion Sensor Light should be automatically activated when
the safe door is opened each time. Light should turn off within
a delay time after the safe door is closed.
PIN CODE REGISTRATION
Safe retains 2 pin codes
1st Safe Default Pin Code : 168
2nd Safe Default Pin Code : 12345678
Changing First Pin Code
1. Press initialization button located on the inside of the safe,
lock will beep twice and yellow indicator light will be lit.
2. Enter desired Pin Code (1-8 Digits) then press “ * ” button.
2 short beeps will be heard and yellow indicator light
will disappear.
3. With door open turn handle counter clockwise to extend the
bolts. Enter registered pin code and press “#” safe should
unlock. Turn handle clockwise and retract bolts; registration
is complete.
Note: If safe does not unlock then pin code registration was
unsuccessful. Please start over with Pin Code Registration.
Changing Second Pin Code
1. Press “ 00 ” on the keypad, then press the initialization
button located on the inside of the safe, lock will beep
twice and yellow indicator light will be lit.
2. Enter second desired Pin Code (1-8 Digits) then press
“ * ” button. 2 short beeps will be heard and yellow
indicator light will disappear.
3. With door open turn handle counter clockwise to
extend the bolts. Enter registered pin code and press
“#” safe should unlock. Turn handle clockwise and
retract bolts; registration is complete.
Note: If safe does not unlock then pin code registration was
unsuccessful. Please start over with Pin Code Registration
