Baroness LM531 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 96

Baroness LM531 Скачать руководство пользователя страница 81

Rear left wheel

8bq62b-212

Lubricating Points_005

Maintenance Work

Removing/Installing Tires

Front Tires

Follow the steps below to remove the front
tires:

Loosen the bolts.

1

lm2ieh-002

Front Tires_001

1

Heat-treated bolt

Securely place the jack beneath the jack-up
point of the front left/right frame area, and
then raise it until the tire lifts off the ground.
"Jack-Up Points" (Page 5-8)
Remove the bolts.
Remove the tire from the wheel mounting
seat.

Important

Tighten the bolts in the tightening order
(diagonally).

For installing the front tires, reverse the
removing procedure.

1.

2.

3.
4.

Rear Tire

Follow the steps below to remove the rear
tires:

Loosen the bolts.

1

upekw4-002

Rear Tire_001

1

Heat-treated bolt

Securely place the jack beneath the jack-up
point of the rear frame area, and then raise
it until the tire lifts off the ground.
"Jack-Up Points" (Page 5-8)
Remove the bolts.
Remove the tire from the wheel mounting
seat.

Important

Tighten the bolts in the tightening order
(diagonally).

For installing the rear tires, reverse the
removing procedure.

1.

2.

3.
4.

Maintenance

LM531

Maintenance

Page 5-13

Maintenance Work

«
...
79
80
81
82
83
...
»

Содержание LM531

































































































Отзывы:

Нет отзывов