Baroness LM531 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 96

Baroness LM531 Скачать руководство пользователя страница 67

1

Grass catcher

2

Grass catcher mounting bracket

3

Mounting pin

Mower units #1, 4 & 5
Note

：

The illustration shows the mower units #1 & 5.
Right and left positions of the grass catcher
mounting brackets differ according to the
location of a mower unit.

1

2

2

3

3

bos35l-012

Removal/Installation of Grass Catcher_002

1

Grass catcher

2

Grass catcher mounting bracket

3

Mounting pin

Transporting

Transporting Procedure

When loading this machine into a trailer or a
truck to transport it, drive the machine in
reverse. When unloading, drive the machine
forward.
If the roof is installed on the machine, remove
it.
The roof may be damaged by wind pressure.

Storage

Before Long-Term Storage

Remove dirt, grass clippings, debris, oil
stains etc. completely.
Supply oil and apply grease to appropriate
parts.
Remove the negative terminal of the battery.

･

･

･

Handling Instructions

LM531

Handling Instructions

Page 4-37

Transporting

«
...
65
66
67
68
69
...
»

Содержание LM531

































































































Отзывы:

Нет отзывов