Baroness LM2400, Руководство по эксплуатации для владельца

Страница: 37 / 75

Principal tightening torques
Tightening Torque by Model
LM2400
Tighten the following bolts and nuts at the torque specified in the table.
For thread locking adhesive, apply a middle strength thread locker (ThreeBond 1322 anaerobic
adhesives).
Location Code Part name
Tightening torque
Thread locking
adhesive
N-m kgf-cm lb-in
Fro
nt wh
ee
l Motor
K0010120902 Bolt, heat-treated M12-90
104 –
134
1,060.49 –
1,366.40
920.50 –
1,186.03
－
Wheel mounting
base
1-20UNEF
Slotted nut for hydraulic
motor 180
–
200
1,835.46
–
2,039.40
1,593.18
–
1,770.20
－
Wheel K0034120352
Bolt, 8T, heat-treated
M12-35P1.5
67
–
85
683.20
–
866.75
593.02
–
752.34
－
Rear
wheel
Wheel mounting
base
1-20UNEF
Slotted nut for hydraulic
motor 180
–
200
1,835.46
–
2,039.40
1,593.18
–
1,770.20
○
Wheel K0034120352
Bolt, 8T, heat-treated
M12-35P1.5
67
–
85
683.20
–
833.75
593.02
–
752.34
－
Tie rod
K1610000020 Tie rod end right ass'y 45 158.87 398.30 －
K1611000020 Tie rod end left ass'y 45 158.87 398.30
－
Engine
K0017100252
Bolt, heat-treated, small,
10-25 P1.25
45
–
57
158.87 –
581.23
398.30 –
504.51
－
Since it may be difficult to tighten bolts and nuts
in the upper front left area of the engine, the
strength category should be 4.8 torque. (See
"Standard tightening torques" (Page 4-13) .)
K4040000150
Nut for attaching anti-
vibration rubber
28
–
38
285.57
–
387.49
247.83
–
336.34
○
Coupling
K0024100351
Bolt, 12T, w/hexagon hole,
M10-35
58 - 76
591.43 -
774.97 513.36 -
672.68
－
K0013100352
Bolt, 11T, heat-treated
M10-35
45
–
76
158.87
–
774.97
398.30
–
672.68
－
K0010100202
Bolt, 11T, heat-treated
M10-20
45
–
76
158.87 –
774.97
398.30 –
672.68
○
K0010080202
Bolt, 11T, heat-treated
M8-20
23 – 38
234.53 –
387.49
203.57 –
336.34
○
Bed knife (bottom
blade)
K0071000092
Screw, heat-treated
flathead M10-20
29 – 38
295.71 –
387.49
256.68 –
336.34
－
Arm frame
Roll bar
K0013120302
Bolt, 11T, heat-treated
M12-45
52
–
67
530.24 –
683.20
460.25 –
593.02
－
Han
dlin
g Instru
cti
ons
LM2400
Handling Instructions
Page 4-15 Tightening torques