Baroness LM101 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 88

Baroness LM101 Скачать руководство пользователя страница 74

Make sure that the bed knife (bottom blade)
contacts the reel cutter (cutting cylinder).

1

1

2

2

A

B

kx7caa-005

Installation of Bed Knife Base_004

1

Reel cutter (cutting cylinder)

2

Bed knife (bottom blade)

3

Gap

4

No gap

Insert one or two strips of newspaper into
the space between the reel cutter (cutting
cylinder) and the bed knife (bottom blade)
at an angle of 90 degrees. Then, rotate the
reel cutter (cutting cylinder)
counterclockwise (as seen from the left side
of the mower frame) by hand to check the
sharpness of the entire range (three or four
points) of the reel cutter (cutting cylinder).

1

2

kx7caa-006

Installation of Bed Knife Base_005

1

Reel cutter (cutting cylinder)

2

Bed knife (bottom blade)

4.

5.

Adjust the positions of the cam bushes so
that both sides cut.

1

kx7caa-012

Installation of Bed Knife Base_006

1

Cam bush

Use a marker, etc., to place a mark on the
mower frame at the position of the punch
mark on the cam bush, and then remove
the cutter pin.

3

2

1

4

kx7caa-029

Installation of Bed Knife Base_007

1

Cam bush

2

Punch mark

3

Cutter pin

4

Mower frame

Remove the bed knife base COMP, and
then install the compression springs and
collars onto the left and right cutter
adjustment bolts.

3

2

4

4

1

2

3

kx7caa-014

Installation of Bed Knife Base_008

6.

7.

8.

LM101

Maintenance

Page 5-22

Maintenance Work

«
...
72
73
74
75
76
...
»

Содержание LM101

























































































Отзывы:

Нет отзывов