Baroness LM101 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 88

Baroness LM101 Скачать руководство пользователя страница 34

1

Cutter adjustment nut

A

Loosen

B

Tighten

Adjustment of Cutting Height

Adjust the cutting height to fit your cutting work.

Important

This applies the set cutting height that differs
from the actual cutting height.

Cutting Height and Thickness of Bed Knife
(Bottom Blade)

Important

The recommended minimum cutting heights
are based on those of common greens.
They may vary according to the green
conditions and machine specifications.
If the green undulation is hard, set it a little bit
higher in order not to damage the green
surface.

Minimum cutting height is recommended for
each thickness of blade as follows.

Type of blade

Thickness of

blade

(mm/inch)

Recommended

minimum cutting

height (mm/inch)

Code

Part name

Remarks

Standard blade

1.5

3.0

K2511000270

1.5 Bed knife (bottom blade) 55G

Standard

2.0

3.5

K2511000280

2 Bed knife (bottom blade) 55G

　

2.5

4.0

K2511000050

2.5 Bed knife (bottom blade) 55G

　

Tipped blade

3.0

4.5

K2510000060

3 Bed knife (bottom blade) 62.5-559

　

5.0

7.0

K2510000160

5 Bed knife (bottom blade) 62.5-559

　

1

2

A

A

33i8xn-002

Cutting Height and Thickness of Bed Knife (Bottom Blade)_001

1

Standard blade

2

Tipped blade

A

Thickness of blade

LM101

Handling Instructions

Page 4-12

Adjustment before Work

«
...
32
33
34
35
36
...
»

Содержание LM101

























































































Отзывы:

Нет отзывов