Barnett Engineering ProTalk Cv3 Скачать руководство пользователя

Страница: 38 / 50

PAGE 34

OPERATIONS

Figure 3 Status Indicators

The indicators are grouped into 5 sections.

1. ALARM GROUP

(6, one for each group)

If the group is disabled:

Off

If the group is enabled:

No alarms in the group

Green

Group alarms are unacknowledged

Flashing Red

Group alarms are acknowledged

Solid Red

Group alarms are being reported

Flashing Yellow

2. ALARM

(12, ten hardware inputs, one power supply monitor & one system alarm)

If the input is disabled:

Off

If the input is enabled:

Configured as an alarm input

(digital, analog, watchdog)

Idle, no alarm

Off

Alarm is unacknowledged

Flashing Red

Alarm is acknowledged

Solid Red

Watchdog Reset Activity

Blink Green

Not Configured as an alarm input

(accumulator, totalizer, interval timer or

special purpose)

Idle

Off

Accumulator or Interval timer

Solid Green

while active

Totalizer

Blink Green

Special purpose - acknowledge

Solid Green

for 500 msec after each operation

Special purpose – shift 1 or 2

Shift 1

Solid Green

Shift 2

Flashing Green

Special purpose – advance shift

Blink Green

Содержание ProTalk Cv3



















































Результаты поиска

Содержание ProTalk Cv3

Отзывы:

Похожие инструкции для ProTalk Cv3

Бренды по названию

Популярные бренды

Barnett Engineering ProTalk Cv3, Руководство по установке и эксплуатации

Результаты поиска

Содержание ProTalk Cv3

Отзывы:

Похожие инструкции для ProTalk Cv3

Бренды по названию

Популярные бренды