page 14
595 ML CRL (S)
800-00177
FIRE PREVENTION
This machine may have several components which are at high temperatures under normal operating conditions, such
as the engine, exhaust system, brake system and transmission.
Clean the machine often. High pressure washing of the machine is suggested every 1000 hours (or 6 months) and
always after a spill.
The following list of hazards provides information which will help to prevent fires:
WARNING
Always keep a fire extinguisher
and first aid kit where they can be
easily reached in case of fire and
keep these items properly
maintained.
Operating personnel should be
instructed on what to do in case
of fire and be required to
demonstrate how to use fire
extinguisher and fire suppression
equipment.
Any portable fire extinguisher or
fire suppression system carried
on the machine that has been
used, should be recharged or
replaced before the machine
resumes operating. Fire
extinguisher manufacturers
recommended service intervals
should be followed.
WARNING
Allow machine to cool down by
idling the engine for a while
before shut-down. Many engine
and transmission fires start after
shut-down.
WARNING
Before adding fuel, shut down
the engine and allow it to cool.
Never smoke while handling fuel
or working on either the fuel or
the hydraulic system.
WARNING
Do not use the machine in areas
with explosive dust or gases that
can be ignited by arcs, sparks,
hot components, or exhaust
fumes.
WARNING
Daily inspect the machine for
flammable debris, removing any
twigs, leaves, straw, rags, fluid
spills or leaks, dirt or grime. Pay
special attention to areas such as
the engine, engine cooling
system, exhaust system, battery,
electrical connections, brake
systems, transmission/drivetrain,
fuel system and hydraulic system.
Clean as often as necessary to
help prevent overheating and
combustion.
WARNING
The electrical system (battery,
electrical connections, etc.) can
be a source of arcs or sparks if
damaged or incorrectly
maintained. Daily inspect all
electrical wiring and connections
for damage. Keep the battery
terminals clean and tight. Replace
or repair any damaged part. Use
proper battery connection and
disconnection procedures.
WARNING
Daily inspect all fuel and
hydraulic oil tubes, hoses, and
fittings for damage and leakage.
Tighten or replace as necessary.
Always clean fluid spills.
WARNING
Do not use ether or starting fluids
on diesel engines with glow
plugs. These starting aids can
explode and injure bystanders.
WARNING
Before doing welding of any kind,
clean machine and disconnect
battery cables. Cover rubber
hoses, battery, and other
flammable parts. Never ground
an arc welder or electrical
accessories through turntable or
boom bearings as arcing may
occur causing bearing damage.
Do not weld on any structural
member unless specifically
authorized by Barko
Hydraulics. Any unauthorized
welding or welding procedures
will void the warranty, and may
cause structural damage.
WARNING
Read the Engine Manual that
comes with every machine for
complete engine operating and
engine safety instructions.
Содержание 595ML
