Barkey warming center III DTM Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 50

Barkey warming center III DTM Скачать руководство пользователя страница 38

Service work

34

Barkey GmbH & Co. KG - Gewerbestrasse 8 - 33818 Leopoldshoehe - Germany - Head Office: +49 (5202) 9801-0

Customer Service: +49 (5202) 9801-30 Fax: +49 (5202) 9801-99 - e-mail: [email protected]

Service manual
Barkey warming center III DTM

7.9

Replacing the microswitch

Removal:

►

Remove the heater insert (see Chapter 7.2).

►

Remove the cover plate (see Chapter 7.2).

►

Undo the nuts from the microswitch using a 14mm jaw spanner, and pull it off the
front panel to the rear.

►

Pull the spade connectors off the microswitch.

Refitting the microswitch:

Refitting the microswitch takes place in reverse order to removal:

►

Press the microswitch into the cutout in the front panel, and tighten the nuts using a
14 mm jaw spanner.

NOTE

The microswitch must be flush with the front panel from behind so that it switches
correctly when the door is closed.

►

Push the spade connectors onto the
microswitch:

– one cable to the middle contact

– the other cable to the rear contact

The polarity is not important.

Figure 35: Microswitch collections

►

Refix the cover plate (see Chapter 7.2).

►

Refit the heater insert (see Chapter 7.2).

«
...
36
37
38
39
40
...
»

Содержание warming center III DTM



















































Отзывы:

Нет отзывов