Barkey warming center III DTM Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 50

Barkey warming center III DTM Скачать руководство пользователя страница 35

Service work

Barkey GmbH & Co. KG - Gewerbestrasse 8 - 33818 Leopoldshoehe – Germany - Head Office: +49 (5202) 9801-0

31

Customer Service: +49 (5202) 9801-30 Fax: +49 (5202) 9801-99 - e-mail: [email protected]

Service manual

Barkey warming center III DTM

►

Reconnect the cables to the me-
chanical overtemperature protection.
The polarity is not important.

Figure 31: Overtemperature protection connections

NOTE

Ensure that the pin-and-socket connectors are plugged together with the flat side
facing downwards, otherwise the cover plate cannot be correctly refitted.

►

Insert the temperature protection into
the heater unit and fix it from the rear
using the screw.

Figure 32: Overtemperature protection fitting

►

Place the heater unit in its original position. In doing so, the heater connecting cable
must be routed in a slight curve underneath the transverse airflow fan.

►

Fix the heater unit with the four screws.

NOTE

Ensure that there is a spacer roll on each screw.

►

Refix the cover plate (see Chapter 7.2).

►

Refit the heater insert (see Chapter 7.2).

«
...
33
34
35
36
37
...
»

Содержание warming center III DTM



















































Отзывы:

Нет отзывов