background image

CASE CLEANING

CASE CLEANING

A periodic cleaning schedule should be established to maintain 
proper  sanitation,  insure  maximum  operating  efficiency,    and  
avoid the corrosive action of food fluids on metal parts that are 
left on for long periods of time.  We recommend cleaning once 
a week.  Further suggestions for case cleaning include the fol-
lowing:

• 

To avoid shock hazard, be sure all electrical power is turned 
off before cleaning.  In some installations, more than one 
disconnect switch may have to be turned off to completely 
de-energize the case.

• 

All surfaces pitch downward to a deep-drawn drain trough, 
funneling liquids to the center of the case where the waste 
outlet is located for easy access.  Check the waste outlet to 
insure it is not clogged before starting the cleaning process 
and avoid introducing water faster than the case drain can 
carry it away. 

• 

To clean the LED luminaires, shut off the lights in the case, 
then  wipe  the  luminaires  down  with  a  soft,  damp  cloth.  
Avoid using harsh or abrasive cleaners as they may dam-
age the lights.  Be certain that the luminaires are complete-
ly dry before re-energizing.

• 

Clean from top to bottom when cleaning the display case to 
avoid cross contamination.

• 

If  any  potentially  harmful  cleaners  are  used,  be  certain 
to  provide  a  temporary  separator  (e.g.,  cardboard,  plastic 
wrap,  etc.)  between  those  cases  that  are  being  cleaned 
and those that may still contain product.

• 

Avoid spraying any cleaning liquids directly on the electrical 
connections.

• 

Allow cases to be turned off long enough to clean any frost 
or ice from coil and pans.

• 

Remove  toekick  and  clean  underneath  the  case  with  a 
broom  and  a  long-handled  mop.    Use  warm  water  and  a 
disinfecting  cleaning  solution  when  cleaning  underneath 
the cases. 

     

D A N G E R

 

SHOCK HAZARD

Always disconnect power to case when servicing 
or cleaning.  Failure to do so may result in serious 
injury or death.

     

W A R N I N G

 

Exercise extreme caution when working in a case 
with  the  coil  cover  removed.    The  coil  contains 
many sharp edges that can result in severe cuts 
to the hands and arms.

14

Содержание AGB
































Отзывы: