background image

Manual 2100-715B 

Page 

21 of 25

SERVICE

FIGURE 10

Fan Blade Setting

TABLE 5

Fan Blade Dimensions

R-410A Refrigerant Charge

This unit was charged at the factory with the quantity of 
refrigerant listed on the serial plate. AHRI capacity and 
efficiency ratings were determined by testing with this 
refrigerant charge quantity.
The following pressure table shows nominal pressures 
for the units. Since many installation specific situations 
can affect the pressure readings, this information 
should only be used by certified technicians as a guide 
for evaluating proper system performance. They shall 
not be used to adjust charge. If charge is in doubt, 
reclaim, evacuate and recharge the unit to the serial 
plate charge

.

"A"

AIRFLOW

MIS-1724

Model

Dimension

A

W12AB

2.25"

Fan Blade Setting Dimensions

Shown in Figure 10 is the correct fan blade setting 
for proper air delivery across the outdoor coil. Refer to 
Table 5 for unit specific dimension.
Any service work requiring removal or adjustment in the 
fan and/or motor area will require that the dimensions 
below be checked and blade adjusted in or out on the 
motor shaft accordingly.

Содержание 11EER WA Series


























Отзывы: