![background image](http://html1.mh-extra.com/html/barco/xdx-series/xdx-series_installation-manual_4265120025.webp)
25
R5914481 /02 XDX
In three-phase operation, the power cord must be rated for
minimum 300 V
in case of a 3W+PE (208V) power
system, and
minimum 500 V
in case of a 3W+N+PE (230/400 V) power system. For a 3W+PE system, 208 V
is measured between the lines. For a 3W +N +PE system, 400 V is measured between the lines, 230 V is
measured between the lines and the neutral.
To protect operating personnel, the National Electrical Manufacturers Association (NEMA) recommends that
the instrument panel and cabinet be grounded. In no event shall this projector be operated without an
adequate cabinet ground connection.
The AC supply must be installed by a qualified electrician in conformance to local codes. Hardware, wire sizes
and conduit types must comply with local codes.
A readily accessible disconnect device shall be incorporated externally to the equipment for removal of the
power to the equipment mains terminals.
The building installation must be provided with a circuit breaker of max. 40 A to protect the complete unit.
WARNING:
Disconnect the power to the unit mains terminals for removal of all power from the unit.
UPS requirements
The Uninterruptible Power Supply (UPS), also known as a Continuous Power Supply (CPS), must have an
output voltage of 200-240 V at 50/60 Hz and must be capable of delivering an output current of 5 A. This UPS
provides only power for the electronics and not for the light source.
The connection between the UPS unit and the UPS inlet of the projector must be done with a certified AC
power supply cord of minimum 1,50 mm² or 14 AWG and minimum 300 V.
The XDX does not have a built in UPS unit.
Projector weight
Do not underestimate the weight of the XDX projector. The projector in frame weights ±206 kg (±454 lbs)
without lens. Ensure that the pedestal or truss on which the projector is installed on or suspended from is
capable of supporting the complete load of the system. Take into account that the projector is too heavy to lift
with people. Use a hoisting mechanism instead.
3.2 Unpacking the projector
What you need to do?
Upon delivery, the projector is packed in a cardboard box upon a wooden pallet and secured with strapping
bands and buckle clips. Furthermore, to provide protection during transportation the projector is surrounded
with foam. Once the projector has arrived at the installation site it needs to be removed from the cardboard
box and wooden pallet in a safe manner, without damaging the projector.
After unpacking let the projector acclimatize to a room temperature between 10°C (50°F) and 35°C
(95°F). It is suggested to only start using the projector after having it stored for a minimum of 16
hours in its final location. Neglecting this may result in a failure in the start-up of the Light Processor
Unit.
Required tools
•
Side cutter
•
Knife
•
Hoisting tool
How to unpack the XDX projector
1.
Remove the strapping bands from the packaging. Use a cutting tool (e.g. side cutter, knife, etc.) to
carefully cut the straps.
Содержание XDX Series
