![background image](http://html1.mh-extra.com/html/barco/s3-series/s3-series_user-manual_3891629019.webp)
2. Safety
2.2
Important safety instructions
To prevent risk, personal injury and Event Master devices damages
Please read this chapter carefully. It includes several cautions to prevent damage to Event Master devices. Ensure that you un-
derstand and follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing Event Master
devices. After this chapter, additional “warnings” and “cautions” are given depending on the installation procedure. Read and follow
these “warnings” and “cautions” as well.
•
Read and follow all installation and operation instructions.
•
Only trained technicians may install Event Master devices.
•
Installation of Event Master devices must be done in a dust free area.
•
Only use attachments/accessories speci
fi
ed by the manufacturer.
•
CAUTION: Troubleshooting must be performed by a trained technician. To reduce the risk of electrical shock, do not attempt
to service this equipment unless you are quali
fi
ed to do so.
•
Refer all servicing to quali
fi
ed service personnel. Servicing is required when the system has been damaged in any way, such
as liquid has been spilled or objects have fallen into the system, or the system has been exposed to rain or moisture, does not
operate normally, or has been dropped.
•
FRAGILE: Event Master devices are fragile. Handle these devices with care at all times.
•
To prevent injury, minimum 2 persons are required to carry an Event Master series processor or an EC–200 controller.
•
Do not remove any covers or panels during normal operation. Removal any of these items will expose sensitive electronic
circuits and the unit may be damaged.
•
During maintenance operations, always switch off thedevice and unplug power cords before removing one of the covers.
•
Always wear a wrist band which is connected to the ground while handling the ESD sensitive parts.
•
Wear insulating gloves during the execution of the installation and maintenance actions to avoid short-circuit.
•
Be careful never to drop anything into the device assembly during the service procedures.
•
Be careful to always follow the procedures during maintenance operations (spare parts replacement).
•
This product is intended to operate from a power source that will not apply more than 230 volts rms between the supply con-
ductors or between both supply conductor and ground. A protective ground connection by way of grounding conductor in the
power cord is essential for safe operation.
•
This product is grounded through the grounding conductor of the power cord. To avoid electrical shock, plug the power cord
into a properly wired receptacle before connecting to the product input or output terminals. A protective-ground connection by
way of the grounding conductor in the power cord is essential for safe operation. For 110V installations the power supply cord
should be rated at 13amps. For 220V installations the power supply cord should be rated 10amps.
•
Use only the power cord and connector speci
fi
ed for your product. Use only a power cord that is in good condition. Refer cord
and connector changes to quali
fi
ed service personnel.
•
Replace spare parts only with the same parts supplied by Barco.
•
Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For
maximum protection, repack your set as it was originally packed at the factory.
•
Rated maximum ambient operating temperature, t
a
= 40°C (104°F).
•
Do not operate this product in an area containing explosive materials.
R5905948 EVENT MASTER DEVICES 17/07/2017
15
Содержание S3 series
