![background image](http://html1.mh-extra.com/html/barco/r9827880/r9827880_owners-manual_4048272040.webp)
R5975765 RCVDS05 020997
40
R5975765 RCVDS05 020997
40
INSTALLATION
INSTALLATION
RCVDS05 to the Red, Green, Blue, H/S sync and V sync inputs of the display 1 using
coaxial cable with BNC connectors.
Repeat these connections respectively for output module 2 to display 2, output
module 3 to display 3 and output module 4 to display 4.
D.2.2. RCVDS05 to AUDIO AMPLIFIER.
Connect the left and right audio outputs of the RCVDS05 (below the most right output
module) to the left and right audio inputs of an audio amplifier using two conductor
audio cables with RCA (cinch) connectors.
D.3. Data communication link between the RCVDS05 and one
BARCO projector.
Only one BARCO projector can have a communication link with the RCVDS05.
Plug the male D9 connector of a communication cable into the female D9 connector
labelled "to projector" on the back plane of the RCVDS05.
Plug the female D9 connector the communication cable into the male connector
labelled "com port (800 peripherals)" on the rear or front panel of the projector
(depending on the type of projector).
E. RCVDS05 USED WITH A CENTRAL COMPUTER
E.1. RCVDS05 connected with a projector.
In this configuration (BARCO projector connected with a RCVDS05 via the BARCO
communication cable) the RCVDS05 is always slave of the projector. The RS232
communication link must be made with the projector and not with the RCVDS05.
No Communication interface module is needed.
E.1.1. Installing the link.
Plug the male D9 connector of a communication cable into the female D9 connector
labelled "to projector" on the RCVDS05.
Plug the female D9 connector of a communication cable into the male D9 connector
labelled "comm port - 800 peripherals" of the projector.
Plug the male D9 connector of serial cable into the female D9 connector labelled
"RS232IN" of the projector.
INSTALLATION
INSTALLATION
RCVDS05 to the Red, Green, Blue, H/S sync and V sync inputs of the display 1 using
coaxial cable with BNC connectors.
Repeat these connections respectively for output module 2 to display 2, output
module 3 to display 3 and output module 4 to display 4.
D.2.2. RCVDS05 to AUDIO AMPLIFIER.
Connect the left and right audio outputs of the RCVDS05 (below the most right output
module) to the left and right audio inputs of an audio amplifier using two conductor
audio cables with RCA (cinch) connectors.
D.3. Data communication link between the RCVDS05 and one
BARCO projector.
Only one BARCO projector can have a communication link with the RCVDS05.
Plug the male D9 connector of a communication cable into the female D9 connector
labelled "to projector" on the back plane of the RCVDS05.
Plug the female D9 connector the communication cable into the male connector
labelled "com port (800 peripherals)" on the rear or front panel of the projector
(depending on the type of projector).
E. RCVDS05 USED WITH A CENTRAL COMPUTER
E.1. RCVDS05 connected with a projector.
In this configuration (BARCO projector connected with a RCVDS05 via the BARCO
communication cable) the RCVDS05 is always slave of the projector. The RS232
communication link must be made with the projector and not with the RCVDS05.
No Communication interface module is needed.
E.1.1. Installing the link.
Plug the male D9 connector of a communication cable into the female D9 connector
labelled "to projector" on the RCVDS05.
Plug the female D9 connector of a communication cable into the male D9 connector
labelled "comm port - 800 peripherals" of the projector.
Plug the male D9 connector of serial cable into the female D9 connector labelled
"RS232IN" of the projector.