![background image](http://html1.mh-extra.com/html/barco/r9827880/r9827880_owners-manual_4048272035.webp)
R5975765 RCVDS05 020997
35
R5975765 RCVDS05 020997
35
INSTALLATION
INSTALLATION
C.1. Signal connection.
C.1.1. RCVDS05 to DISPLAY.
Connect the video output of the RCVDS05 to the video input of the display using a
coaxial cable with BNC connectors.
Connect the S-Video output of the RCVDS05 to the S-Video input of the display using
a 4-wire coaxial cable with 4 pin plugs.
Connect the Red, Green, Blue, H/S sync and V sync outputs of the RCVDS05 to the
Red, Green, Blue, H/S sync and V sync inputs of the display using coaxial cable with
BNC connectors.
When using an RCU to control the RCVDS05, the RCU address must be set to "9"
or "0". When the address is set to "0", the RCVDS05 and all projectors in the room
will listen to the IR commands.
With address "9", it is possible to control only the RCVDS05.
If you want to control the RCVDS05 with an RCU on another address other than "0"
or "9", a communication interface module must be installed (see Special modules).
With this module, it is possible to set the RCVDS05 address between 0 and 15. Only
the addresses between 0 and 9 are valid when using an RCU.
Hint :
the address can be displayed on the RCVDS05 by pressing the ADDR key on
the RCU. During 1.5 sec. an A.x is displayed, where x has a value between 0 and
F (hex).
C. RCVDS05 USED AS STAND ALONE SWITCHER.
R
L
R
L
R
TO P ROJECTOR
98 28020
98 27930
98 27920
To Video
input Display
To RGBH
input
Display
To S-Video
input Display
To audio
amplifier
INSTALLATION
INSTALLATION
C.1. Signal connection.
C.1.1. RCVDS05 to DISPLAY.
Connect the video output of the RCVDS05 to the video input of the display using a
coaxial cable with BNC connectors.
Connect the S-Video output of the RCVDS05 to the S-Video input of the display using
a 4-wire coaxial cable with 4 pin plugs.
Connect the Red, Green, Blue, H/S sync and V sync outputs of the RCVDS05 to the
Red, Green, Blue, H/S sync and V sync inputs of the display using coaxial cable with
BNC connectors.
When using an RCU to control the RCVDS05, the RCU address must be set to "9"
or "0". When the address is set to "0", the RCVDS05 and all projectors in the room
will listen to the IR commands.
With address "9", it is possible to control only the RCVDS05.
If you want to control the RCVDS05 with an RCU on another address other than "0"
or "9", a communication interface module must be installed (see Special modules).
With this module, it is possible to set the RCVDS05 address between 0 and 15. Only
the addresses between 0 and 9 are valid when using an RCU.
Hint :
the address can be displayed on the RCVDS05 by pressing the ADDR key on
the RCU. During 1.5 sec. an A.x is displayed, where x has a value between 0 and
F (hex).
C. RCVDS05 USED AS STAND ALONE SWITCHER.
R
L
R
L
R
TO P ROJECTOR
98 28020
98 27930
98 27920
To Video
input Display
To RGBH
input
Display
To S-Video
input Display
To audio
amplifier