Barco PGWU-62K, Руководство по безопасности

Страница: 6 / 57

6
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/20
ENGLISH
Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector
y
and to protect it from overheating, these openings must not be blocked or covered. The openings should never
be blocked by placing the projector too close to walls, or other similar surface. This projector should never be
placed near or over a radiator or heat register. This projector should not be placed in a built-in installation or
enclosure unless proper ventilation is provided.
Projection rooms must be well ventilated or cooled in order to avoid build up of heat.
y
Let the projector cool down completely before storing. Remove cord from the projector when storing.
y
To prevent projector damage
The air filters of the projector must be cleaned or replaced on regular base (a “clean” booth would be monthly-
y
minimum). Neglecting this could result in disrupting the air flow inside the projector, causing overheating.
Overheating may lead to the projector shutting down during operation.
The projector must always be installed in a manner which ensures free flow of air into its air inlets and
y
unimpeded evacuation of the hot air from its cooling system.
In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic
y
Compatibility (EMC) requirements, it should always be operated with all of its covers in place.
Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and
y
to protect it from overheating, these openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed
near or over a radiator or heat register. The device should not be placed in a built-in installation or enclosure
unless proper ventilation is provided.
Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug
y
the mains supply immediately. Do not operate the projector again until it has been checked by qualified service
personnel.
Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects
y
may not be nearer to the projector than 30 cm (12”) on any side.
Do not use this equipment near water.
y
Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as
y
high power laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the
Digital Mirror Devices™ in which case there is a loss of warranty.
Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror
y
Devices™ in which case there is a loss of warranty.
Save the original shipping carton and packing material. They will come in handy if you ever have to ship your
y
equipment. For maximum protection, repack your set as it was originally packed at the factory.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use
y
a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since
these will damage the cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild
detergent solution.
To ensure the highest optical performance and resolution, the projection lenses are specially treated with an
y
anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do
not use a damp cloth, detergent solution, or thinner.
Rated maximum ambient temperature, ta= 40 °C (104 °F).
y
This projector can be set to any angle within vertical 360° range. It can also rotate 90° into portrait orientation.
y
However, aside from portrait projection, this projector cannot be installed at a leftward or rightward slant.