Barco HDF W series Скачать руководство пользователя страница 149

Страница: 149 / 319

11. Lamp

11. LAMP

•

Lamp menu overview

•

Lamp power mode

•

Lamp power

•

Auto dimming when on Pause

•

Auto dimming when No Signal

•

Auto dimming when Over-temperature

•

CLO mode (Constant light output mode)

•

•

•

•

11.1 Lamp menu overview

Overview table

Level 1

Level 2

Level 3

Lamp

Power

Power mode

Power

Auto dimming when pause

Auto dimming when No Signal

Auto dimming when Overtemperature

CLO mode

CLO targets

LPS Power

Identi

cation

Z-axis

Light output

11.2 Lamp power mode

What can be done?

The lamp power mode can be switched between

Normal

Economic

and

Long Life

. When playing in Economic and Long Life

mode, the lamp life time will be higher than in normal mode.

The counter of the lamp life time counts equal for normal or economic mode but the customer will see that the ageing of the lamp is
lower in economic and long life mode.

Normal : maximum allowed power is fed to the lamp. Maximum light output is reached in this way.

Economic : a reduced wattage is fed to the lamp. Reduced light output but a longer life time for the lamp.

Long Life : wattage fed to the lamp reduce to 75%. Reduced light output but a longer life time for the lamp.

The lamp power mode setting is linked with the CLO mode setting. When CLO mode settings is set to

, the lamp power mode

setting is ignored and projector will play in CLO mode. Once the CLO mode setting is switched to

Off

, the installed lamp power

mode setting will be used.

How to switch

Press

Menu

to activate the menus and select

Lamp

→

Power

→

Mode

Image 11-1
Main menu, lamp

Image 11-2
Lamp, power

R5905158 HDF SERIES 16/06/2015

145

Содержание HDF W series
































































































































































































































































































































Результаты поиска

Содержание HDF W series

Отзывы:

Бренды по названию

Популярные бренды

Barco HDF W series, Инструкция по использованию и установке

Результаты поиска

Содержание HDF W series

Отзывы:

Бренды по названию

Популярные бренды